- add mtd-utils to PACKAGE_LIST_BOARD.
- this should be enough to wipe Petitboot;
- more investigative work and u-boot building is needed for SPI+SATA boot
Signed-off-by: Ricardo Pardini <ricardo@pardini.net>
* Upgrading sunxi and sunxi64 EDGE to 5.13
Both variants tested for building
* Bump imx6 to 5.13.y
Tested
* Bump Jetson nano kernel to 5.13.y
* Move mvebu and mvebu64 edge to 5.13.y
* add DFI driver to provide hardware-based memory controller load
* adapted DRAM Memory Controller driver from rk3328, add necessary headers
* provide device tree overlays to enable DDR3 clock scaling
* adapted rk322x-box to allow DDR speed bin selection to user
* add ipb900 board gpio configuration
* add rtl8723cs driver to linux-current kernel
* use ddrbin v1.10 set to 330 Mhz at boot
* provide overlays for ddr3 at 330, 528, 660 and 800 mhz
* split emmc overlays to enable options by user choice
* modified rk322x-config to support dmc, emmc overlays
* remove optee trust os in favor of rockchip proprietary blob
for dmc functionality
* [ Rockchip64 ] Add Tinker Board 2
Using Mainline ATF/U-boot/Kernel
What works:
- USB (NOT TYPE C)
- PCIe
- LED's
- Ethernet
- HDMI
TODO:
- Type-C (fusb302 stuff)
- Type-C DP
- Regulators for big cores and GPU (sitting at default values now, no DVFS)
- Formware/driver for RTL8822CE
U-boot spits out some trash right after handing off control from SPL to U-Boot,
but doesn't impact boot. Needs looked at.
* [ rockchip64 ] remove unrelated changes to 369ab2decdc5a3c49973d8eeb783c95558dcc41a
* [ rockchip64 ] fix merge mess from symlinks step 1
* [ rockchip64 ] fix merge mess from symlinks step 2
* [ rockchip64 ] fix merge mess from symlinks step 3
* [ rockchip64 ] add asus driver for FAN53200 regulator
* Rename tinkerboard.conf to tinkerboard.wip
set as WIP for merge to trunk. Not ready for images just yet.
* revert rename to wip
wrong tinkerboard
* Rename tinkerboard-2.conf to tinkerboard-2.wip
prepare for merge to trunk. Not ready for images
* Tinker Board 2 GPU and Type-C
Support USB3 over type-C connector. display Port is still non-functional, framework in device tree however
Enable GPU
* Tinkerboard 2 DTS tweaks
Added this round:
Type-C DP now works
thermal sensors enabled (oops)
* Tinker Board 2 update config
-Adds wifi support for the RTL8822
* remove obsolete and broken patch for pine64so u-boot
This prevents the image from being built.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
* sunxi: fix pine64so phy-mode and add yt8511 support
Pine A64-LTS board should have RGMII-TXID mode instead of RGMII-ID (the
Realtek PHY chip's RXID is sometimes broken).
In addition, new Pine A64-LTS v2 board will use YT8511 instead of
RTL8211E, which still works under RGMII-TXID mode.
Backport YT8511 driver and phy-mode change from linux-next.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Co-authored-by: Igor Pečovnik <igorpecovnik@users.noreply.github.com>
* Move Jetson patches to right location, add upstream patch
Also add upstream patch for sunxi
* Add upstream patches for Odroidxu4 current
* Add meson64 upstream patches
* Remove unnecessary patch
- this patch works when compiling and installing manually.
- the dtb with the changes is taken from the kernel and not from u-boot, therefore this patch does not work.
* Add enable-audio-codec-bpim2ultra-kernel.patch
- Add patch to enable audio codec in bpi-m2-ultra with h3 compatible
- Built and tested on Armbian Buster with Kernel 5.11.x (edge)
* Bpi-M2-Ultra enable audio on branches
- This finishes enabling the audio codec in the other kernels (5.4 - 5.10 - 5.11)
- Remove patch from u-boot folder (my bug)
- Compiled and tested in their respective kernel with debian buster
* Bpi-M2-Ultra enable audio kernel 5.12
- add patch to kernel 5.12
* Improve sunxi fix-a64-timejump.patch
Current patch still throws BUG:
WARNING: CPU: 2 PID: 31 at drivers/clocksource/arm_arch_timer.c:364 sun50i_a64_read_cntpct_el0+0x2c/0x38
Cause: Timer values are required to be exactly the same, while it may increase in between reads. Seems to happen especially during boot
Timer values are like: x2 : 0000000015014561 - x0 : 0000000015014567
Solution: Normalize timer values and return normalized value.
* Add patch for 5.12.y
Note. Small changes on upstream solution:
GENMASK(9, 0 ... -> GENMASK(8, 0 ...
Co-authored-by: Igor Pecovnik <igor.pecovnik@gmail.com>
* Bump imx6 edge to 5.12.y
* Bump odroid xu4 edge to 5.12.y
* Bump Jetson nano edge to 5.12.y
* WIP: Bump sunxi to 5.12.y
- create a copy of patches and make a new link
- wireless patches needs adjutement to 5.12
- some patches are still failing
* Adjust wireless patches to build on 5.12.y
* Remove template wireless patch
* Move Espressobin edge to 5.12.y
* Bump mvebu to 5.12
- patch 92-mvebu-gpio-remove-hardcoded-timer-assignment.patch was disabled @heisath
- adjusted wireless driver for 8723ds
* Adjust sunxi / sunxi64 edge to compile
* Fix kernel config for Jetson nano edge
* bump meson64 to 5.12.y
* bump rockchip edge to 5.12.y
* Bump rockchip64 to 5.12.y
* Bump rk322x edge to 5.12.y
@paolosabatino
* Cleanup im6, re-add 5.10.y patches since one is missing in 5.12.y
* Update odroidxu4 edge links
* rk322x: moved rk322x-edge to kernel 5.12, fix overlay compilation, retouched included kernel modules
* Cleanup: remove deprecated config
Co-authored-by: Paolo Sabatino <paolo.sabatino@gmail.com>
* Remove unnecessary patch
- this patch works when compiling and installing manually.
- the dtb with the changes is taken from the kernel and not from u-boot, therefore this patch does not work.
* Add enable-sound-pinecube-kernel.patch
- Add patch to enable audio codec in pinecube with v3s compatible
- Built and tested on Armbian Buster with Kernel 5.11.x (edge)
A long story short:
- patch 'meson64_add_shutdown_function_to_meson_drv.patch' (adds meson_drv_shutdown) added on 04/03/2021
- same patch renamed to '.patch_disabled' on 07/03/2021, since it broke what it was supposed to fix
- kernel 5.10.24 upstream merged similar version of patch, which indeed fixed some khadas stuff, but broke odroid, at least HC4
- now I add this patch to revert upstream.
- also remove the .patch_disabled to avoid confusion
- to say the truth, the HC4 is not reboot-proof, it still hangs sometimes. so this is not the end of it.
- ps: without this revert, HC4 hangs 100% of the time.
- ps2: did not test on edge 5.11 yet, but it looks like the same
Signed-off-by: Ricardo Pardini <ricardo@pardini.net>
There are already emmc nodes in rk3288-tinker-s.dts, adding these nodes
to rk3288-tinker.dtsi will cause emmc busy loop on original Tinkerboard.
Signed-off-by: Jack Chen <redchenjs@live.com>
Adds Xilinx Bootgen tools to build environment (alongside sunxi-tools, etc ..)
Adds new SoC family Zynq (7000 series, not MP/UltraScale)
Adds new board Avnet MicroZed
* add device tree overlays to handle boards with power regulation issues,
* fix misconfiguration issues in overlays
* add missing wireguard module for rk322x-current and -edge
* Re-enable network checksum TX offload on rockchip64 family
* Adjust gmac PBL setting for rk3399 legacy to fix network issues with MTU 1500
* Adjust gmac PBL setting for rk3328 in rockchip64-legacy to fix network issues with MTU 1500
Co-authored-by: Piotr Szczepanik <piter75@gmail.com>
- Enabled nfc on rk322x-dev and disable on rk322x-current (need further development)
- Tidied up rk322x-current device tree
- enabled nfc rockchip driver enabled in rk322x-dev kernel config
- Enabled EHCI controller in u-boot (added patch for inno-phy, device tree and config bits), better device detection for dwc2 usb otg port
- Removed SPL_FIT_GENERATOR from u-boot configuration, fixed .its file to use binman
- fixed rk322x its file (now includes dtb), reverted u-boot to v2020.10 and changed dev_* into log_debug() calls
* Adjust the RK808 buck step to improve stability
* Adjust vdd_log and enable vdd_center init voltage
For some reason, regulator-init-microvolt property under PMIC does not applied. Set the voltage on board file.
* Explicitly set vdd_log voltage for NanoPi M4V2 - possibly fix stability issues
* Regulator tweaks for NanoPi M4V2
* Add vdd_log to kernel and switch vdd_center back to 900mV
* Switch vdd_center to 0.95
* Make rk80x bucks voltage steps shorter to make the NanoPi M4V2 stable
* Tweak u-boot config for NanoPi M4V2
* Made the rk808 voltage steps configurable and configured 50mV for NanoPi M4V2
* Bump rockchip DEV 32b to 5.11.y
* Move mvebu64 DEV to 5.11.y
* Move Rockchip64 DEV to 5.11.y
Disabling general-rkvdec_nv15.patch - need more attention
* Add Meson DEV / Odroid C1
* Move OdroidXU4 DEV to tobetter's 5.11.y branch
* Bump sunxi DEV to 5.11.y
* Bump mvebu DEV to 5.11.y
* mvebu: Patch kernel to fix SATA write performance regression
Add an upstream patch that fixes SATA write speed regression that
appeared in kernel 5.9.
Signed-off-by: Maxim Mikityanskiy <maxtram95@gmail.com>
* Create 0001-Revert-block-simplify-set_init_blocksize-to-regain-l.patch
Co-authored-by: Igor Pečovnik <igorpecovnik@users.noreply.github.com>
- for manual/auto control of pwm fan (in the ODROID HC4 for example)
- original is at 8a63de9e2a
- discussion https://patchwork.kernel.org/project/linux-hwmon/patch/20201125163242.GA1264232@paju/
- I'd be much happier with a cooling map in the DTB, but this makes my fans spin correctly via fancontrol
- this affects all of meson64, but only for PWMs that are already exposed to hwmon
Signed-off-by: Ricardo Pardini <ricardo@pardini.net>
* Enable RTC (hym8563) for Station P1 in mainline (renaming DT in process)
* Switch Station P1 to rockchip64
* Fix linking for Station P1 device tree in legacy
* rockchip64: Added XHCI HCD USB TRB ENT quirk
On some xHCI controllers (e.g. Rockchip RK3399/RK3328/RK1808), they need
to enable the ENT flag in the TRB data structure to force xHC to
prefetch the next TRB of a TD.
Enable the quirk on RK3399 through device tree node properties.
Ported from Rockchip Linux 4.19
* add to dev branch
Polished and fixed xt-q8lv-10 rockchip-legacy dtb
Reworked act8846 reboot patch for rockchip-legacy (applies, but not yet working though)
Renamed kernel updated patches in rockchip-legacy directory adding "04-" prefix to make them uniform with existing
This patch (most likely taken from OpenWrt) only applies to ARMADA-XP
hardware, none of which is supported by Armbian.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Sound node recovered from Pull Request #408
Sound node name changed in line with tinkerboard & xt-q8l, cf. issue #1367
Also added missing i2s node, cf. http://rockchip.wikidot.com/hdmi-audio
HDMI audio now confirmed working on Miqi clone, Openhour Chameleon
These patches are for Olimex S3-OLinuXino, which is not yet support by
Armbian.
Remove them to prevent DT node conflict.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
RK3399 maximum clockspeed according to Rockchip is 1.8 GHz for all but a couple variants. Almost all SBC's use 1.8 GHz silicon.
Remove automatic application of extra 2 GHz opp, allow user to select an overlay at their own risk.
RK3399 maximum clockspeed according to Rockchip is 1.8 GHz for all but a couple variants. Almost all SBC's use 1.8 GHz silicon.
Remove automatic application of extra 2 GHz opp, allow user to select an overlay at their own risk.
- curently attached to RC7 as https://github.com/armbian/build/pull/2378
- config derived from current and contains all latest changes
- dirty reboot and eth0 reset hacks are not added and can be added later if still needed (need_check subfolder)
* mvebu-dev: refresh all patches with quilt
Cleaned up based on kernel 5.9.12.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
* mvebu-current: refresh patches with quilt
Based on kernel version 5.9.12
Signed-off-by: Rosen Penev <rosenp@gmail.com>
* mvebu-legacy: refresh patches with quilt
Based on kernel 4.19.161
Signed-off-by: Rosen Penev <rosenp@gmail.com>
* mvebu-legacy: remove custom helios4 dts file
This is already added upstream. No need to have it here.
Continued refreshing the other patches.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
* Add WIP support for Orangepi Zero 2
* squeeze H616 patches into sunxi-dev
* Update linux-sunxi64-dev.config
* H616: Limit CPUMAX
* Enable DEV only
* H616: remove patches from sunxi-current
* H616: apply new patchset
Co-authored-by: EvilOlaf <werner@armbian.de>
Co-authored-by: Werner <EvilOlaf@users.noreply.github.com>
