* rk322x: add support for ssv6030p (disguise it as ssv6051p)
* rk322x: enable BPF filters and ancillary options, remove ssv6030 patches
* rk322x: enable BPF filters for edge 5.17 kernel
* Update linux-media-current.config
Adding thermal / temperature monitoring support for jetson nano
* Update linux-media-edge.config
Adding thermal / temperature monitoring support for jetson nano
* rk35xx: enable the CONFIG_F2FS_FS_COMPRESSION option
This allows to use compression on a F2FS partition to save space and
reduce I/O operations to media.
* all: enable the CONFIG_F2FS_FS_COMPRESSION option
* Add reg_ahci_5v status okay for bananapro board
* Bananapro: add AXP209 regulators
* Fix series.conf, Disable the patch that is not being applied.
* Fix linux-sunxi64-edge.config for v5.17.3
* Fix linux-sunxi-edge.config to v5.17.3
* Switch EDGE to core 5.17 for sunxi
* Remove the old rtl8723cs driver which is incompatible with the new kernel and cannot be used.
* Use AUFS if the kernel version is less than 5.16
* Print the last 20 lines of the log if the kernel compilation failed.
* Set KERNEL_VERSION_LEVEL to 5.17
Co-authored-by: Igor Pecovnik <igor.pecovnik@gmail.com>
add CONFIG_GPIO_SYSFS=y to linux-sunxi64-current.config and linux-sunxi64-edge.config
remove if EXPERT from /sys/class/gpio/... (sysfs interface) in /drivers/gpio/Kconfig
* Rockchip64 Linux-5.10y - drivers for Motorcomm YT8531
renamed the previous "net-phy-Add-driver-for-Motorcomm-YT85xx-PHYs.patch" to "net-phy-Add-driver-for-Motorcomm-1-YT85xx-PHYs.patch" to fix patch order and added a new patch "net-phy-Add-driver-for-Motorcomm-2-YT8531-PHYs.patch"
The new YT8531 patch is sourced from from Lean's OpenWrt source rockchip/patches-5.10/601-net-phy-Add-driver-for-Motorcomm-YT8531-PHYs.patch.
It is intended to extend a patch identical to Armbian's "net-phy-Add-driver-for-Motorcomm-YT85xx-PHYs.patch" and is used without alteration.
* Add new board OrangePi R1 LTS (rk3328)
Includes uBoot and support for Linux-5.10y
* Rockchip64 Linux-5.15y drivers for YT8531 and other Motorcomm chips
YT8010, YT8510, YT8511, YT8512, YT8521. The driver patch set is sourced from Xunlong-OrangePi OpenWRT and is used as is, with only a name and makefile change.
A single patch set uses the same underlying source code as the Armbian Linux-5.10y set, but uses inbuilt logic to apply tweaks that depend on the Linux kernel version.
The patch is renamed similarly to the 5.10 patch set, net-phy-Add-driver-for-Motorcomm-T85xx+PHYs.patch to imply code base continuity with the previous similar Armbian patch sets.
* Rockchip64 Linux-5.15y support for Orange Pi R1 Plus LTS
Includes DTS and makefile changes. A driver for net phy YT8531C is in a separate commit
* change orangepi-r1plus-lts.csc to orangepi-r1plus-lts.conf
board is now supported
* - add patch also to 5.16.y
- fix wrong patch permission
* Fix Makefile patch
Co-authored-by: Igor Pecovnik <igor.pecovnik@gmail.com>
* Switched rockchip64-current to linux 5.15
* Backported and adjusted patches from rockchip64-current
* Switched rockchip64 edge to 5.16.y (#3499)
* Initial rockchip64-edge at 5.16.y
* Bunch of fixes for rockchip64-edge at 5.16.y
Co-authored-by: Igor Pečovnik <igorpecovnik@users.noreply.github.com>
* Prepare xu4 edge for 5.16.y, move current of imx6 to 5.15.y and edge to 5.16.y
- fix bootsplash on 5.16.y
* rk322x: advance current to 5.15 and edge to 5.16
* rockchip: advance current kernel to 5.15, edge to 5.16
* - adjust configs
- fix bootsplash patches
- adjust aufs
* Switch sunxi / sunxi64 current to 5.15.y, edge to 5.16.y
- cleanup bootsplash patches
- adjust configs
* Update mvebu64
Co-authored-by: Paolo Sabatino <paolo.sabatino@gmail.com>
* Support edge kernel for Rock 3A and rk35xx
* Removing patch email headers
There is also some script floating around to do this automatically when pooling from patchwork
* Update rk356x-usb2-support.patch
* Remove email headers
* Remove email headers
* Remove email headers
* Update config and change edge branch
* Enable edge beta build
* Refresh the rk35xx patches and update the dts
Remove also previous wireless patches related to IPX removal
* Removing hirsute target
deprecated
Co-authored-by: Catalin Toda <catalinii@yahoo.com>
Co-authored-by: Igor Pečovnik <igorpecovnik@users.noreply.github.com>
Co-authored-by: Igor Pecovnik <igor.pecovnik@gmail.com>
* Several improvements for RPi builds
- attach to RPi kernels
- current (ubuntu) -> legacy
- current -> 5.10.y, edge, 5.15.y
* Move current Rpi to 5.15.y and edge to 5.16.y
When NFSD is enabled as module, kernel does not compile. But it works as build in. Since its pretty pointless to fix in the code, lets use this workaround.
FYI @patrickbkr
* Sync kernel config with radxa and remove packaging patch
* Merge the rockchip64 legacy config as well
* Lower priority of EFI partitioning against DOS partitioning which is used by Armbian
Co-authored-by: Catalin Toda <catalinii@yahoo.com>
* extensions framework (née "fragments")
- this should actually change nothing at this point, just add capabilities
- the framework is implemented in lib/extensions.sh
- the "if function x exists then call x" replaced with call_extension_method()
- +inline documentation
- +compatibility names
Signed-off-by: Ricardo Pardini <ricardo@pardini.net>
* extensions framework; meta-extensions: auto-docs and sample extension gen
- 2 extensions dealing with extensibility itself
- detect-unused-extensions: shows which extensions are enabled, but never called.
- gen-sample-extension-docs: generates a sample empty extension & Markdown documentation for extensions
Signed-off-by: Ricardo Pardini <ricardo@pardini.net>
* new extension methods and features via config variables in core Armbian
- `SKIP_EXTERNAL_TOOLCHAINS=yes` - does not download or use any linaro toolchains, only build host-installed ones
- `SKIP_BOOTSPLASH=yes` - does not patch kernel for splash file
- `EXTRA_BSP_NAME=xyz` - allows for BSP variants, useful for when extensions modify the BSP
- `EXTRA_ROOTFS_MIB_SIZE=x` - add x mib's to rootfs size, for use with very small images
- `KERNEL_EXTRA_TARGETS` - what extra targets to make kernel for, default to "modules dtbs"
- `BOOTCONFIG=none` - does not build nor install u-boot; also doesn't handle bootscripts et al
- `unset KERNELSOURCE` - does not build nor install kernel, nor build initrd, nor build nor install firmware
- `ARMHF_ARCH=skip` - does not add armhf to apt/dpkg, thus pure arm64
- `SKIP_ARMBIAN_REPO=yes` - results in armbian.list.disabled in the final image
- define `APT_EXTRA_DIST_PARAMS` with apt-cacher-ng options and use it for `PACKAGE_LIST_INSTALL/REMOVE` et al
- initial support for targeting x86/amd64 UEFI and BIOS
- some do's/don'ts for x86/amd64, like a different `UBUNTU_MIRROR` default
- GPT/EFI(ESP) partitions (fat, `UEFISIZE=256` to enable, mount `UEFI_MOUNT_POINT=/boot/efi`, first on disk but ends
up at `$uefipart`=15)
- GPT/BIOS partitions (fat, `BIOSSIZE=1` to enable, second on disk but ends up at partition 14)
- `UEFI_FS_LABEL="armbiefi"` - to set the FAT label for the EFI partition, visible in Win/Mac
- hard-requires gdisk package host-side
- add add_host_dependencies() extension method; fill `EXTRA_BUILD_DEPS="pkg pkg2"` to install to host before toolchains
download
- add pre_prepare_partitions() extension method, for custom partition size calculations
- add create_partition_table() extension method, used to do full-custom partitioning if `USE_HOOK_FOR_PARTITION=yes`
- add post_create_partitions() extension method, mostly for easy debugging
- add post_write_sdcard() extension method, where you can also set `SKIP_VERIFY=yes` to skip sdcard verification
- add post_install_kernel_debs() extension method.
- multiple fixes to bsp to avoid spurious errors when files are not where it expects
- v4: detect `update-initramfs` failure and abort build with useful message if it does
- v4: show useful stacktrace in `exit_with_error`
- if `ERROR_DEBUG_SHELL=yes`, drop into a shell before unmounting/deleting everything, so we can inspect what went wrong
- v4: display a message before `apt-get remove PACKAGE_LIST_BOARD_REMOVE` packages, so any errors while removing are easy to understand
- v4: preserve kernel .config's dates when copying
Signed-off-by: Ricardo Pardini <ricardo@pardini.net>
* extensions framework; refactor tool fetching/building into extensions
- a few examples of core refactoring using extensions
- sunxi-tools extension, enabled by 2 different sunxi family includes ("reuse" example)
- marvel-tools extension, enabled by 2 different mvebu family includes
- rkbin-tools extension, enabled by rockship64_common family include
- amlogic-fip/c2-blobs stuff refactored directly into meson64_common.inc ("single-use" example)
- removed the 'testings' fetch_from_repo completely since not used anywhere.
Signed-off-by: Ricardo Pardini <ricardo@pardini.net>
* .wip's for UEFI arm64 and UEFI/BIOS x86 via new GRUB extension
- v3: added `growroot`-awareness to `armbian-resize-filesystem`
- the partition-growing part of `armbian-resize-filesystem` does not deal correctly with the UEFI layout
- `growroot` is installed on UEFI images by default, that handles growing partition during initramfs
- now `armbian-resize-filesystem` handles `resize2fs` only, and works.
- v4: reworked UEFI board/family/include structure:
- use Distro's `linux-generic` kernel only for `current`
- `edge` now builds it's own pure-mainline `5.15.y` kernel, for both x86 and arm64
- `.config` taken from Ubuntu, probably needs tuning for EXTRAWIFI=yes et al
- v4: introduce `SKIP_KERNEL_SYMLINK=yes`, tested in `builddeb`
- to avoid symlinking kernel; u-boot likes it, but grub and flash-kernel hates it
- v5: many fixes
- v7: more small fixes.
Signed-off-by: Ricardo Pardini <ricardo@pardini.net>
* .wip for the RaspberryPi 4B via new flash-kernel extension
- this does not build it's own kernel "yet", but uses default linux-raspi kernel from Ubuntu
- flash-kernel is not really a bootloader
- it just prepares kernel et al a FAT partition for booting by the RPi4b bootloader
- flash-kernel is standard Debian package, but has only been tested on Ubuntu releases
- it is really only known-working since Hirsute release.
- Debian's rpi kernel is armhf only, so out of scope here, at least until we add source-built kernels.
- v3: fixed focal rootfs build. untested.
- v3: better variable names, preparing for source-built kernel.
- v5: new edge build with pure mainline kernel.
- v6: many fixes and some hacks for packaging and layout, also firmware (using Ubuntu's)
Signed-off-by: Ricardo Pardini <ricardo@pardini.net>
* Added first patch to edge x86 related to wifi drivers
* extensions: leave hostapd alone; remove hackish ext; block reentrancy
- package-list-utils does not belong in this PR
- grub or bcm2711 is not the place to remove hostapd
- block recursive enable_extension() calls, for now.
Signed-off-by: Ricardo Pardini <ricardo@pardini.net>
* gen-sample-extension-docs: fix: avoid counter in generated sample
Signed-off-by: Ricardo Pardini <ricardo@pardini.net>
* extensions: dependencies: enable_extension() in extensions with a stack
- and better stacktraces, I hope
Signed-off-by: Ricardo Pardini <ricardo@pardini.net>
* Remove code from package list since we don't have it in repository
Adjust kernel config to disable driver that needs further polishing.
* Allow amd64 to build the same desktops as aarch64. We only have this limit for armhf, where some desktops don't work
* amd64: allow building amd64 on aarch64 with system toolchain
- conditionally add gcc-x86-64-linux-gnu to hostdeps
Signed-off-by: Ricardo Pardini <ricardo@pardini.net>
* add libelf-dev directly to hostdeps (and Dockerfile), remove extension
Signed-off-by: Ricardo Pardini <ricardo@pardini.net>
* packaging: remove SKIP_KERNEL_SYMLINK hack, fix the root cause
- which was the missing $image_name for non-arm64 & non-arm, so: x86 for example
Signed-off-by: Ricardo Pardini <ricardo@pardini.net>
* grub: really obliterate u-boot stuff from BSP
- for now. soon we'll refactor u-boot so not have to do this
Signed-off-by: Ricardo Pardini <ricardo@pardini.net>
* flash-kernel: really obliterate u-boot stuff from BSP
- for now. soon we'll refactor u-boot so not have to do this
Signed-off-by: Ricardo Pardini <ricardo@pardini.net>
* extensions: add host_dependencies_ready() hook
- this passes FINAL_HOST_DEPS containing all hostdeps for the run after they're installed
Signed-off-by: Ricardo Pardini <ricardo@pardini.net>
* Add verification functions for correct selection.
* If UEFI Skip symlink creation
* Do not create dtb package for amd64
* Skip scripts folder cleaning if build process native.
Skip creating postinst prerm scripts for headers.
* Skip applying headers-debian-byteshift.patch if build native
* Fix architecture syntax as x86_64
* Revert "amd64: allow building amd64 on aarch64 with system toolchain"
This reverts commit 0c5ee20bb1.
* Compare architectures before starting compilation.
Signed-off-by: The-going <48602507+The-going@users.noreply.github.com>
* extensions: cleanups after fixes by the-Going
- packaging:
- there is _no need_ anymore for the symlink hack, CONFIG_EFI or no. But check is great, see below
- it's not `amd64` that has no DTB's, it's all UEFI, thus: `is_enabled CONFIG_EFI`, thanks!
- Explicitly disallow "reverse cross compile" in amd64.conf.
- whitespace-only-deletions: revert. we shall shellfmt the whole thing one day, but not today.
- fix a few syntax warnings in newly introduced code (floating `$ARCH` vs `"${ARCH}`) - blame shellcheck
Signed-off-by: Ricardo Pardini <ricardo@pardini.net>
* packaging: fix: turns out a lot of boards have CONFIG_EFI=y, can't use that for dtb/no-dtb decision.
Signed-off-by: Ricardo Pardini <ricardo@pardini.net>
* grub: remove debug
Signed-off-by: Ricardo Pardini <ricardo@pardini.net>
* firmware: allow installing `armbian-firmware-full`; make it really full
- can now use `BOARD_FIRMWARE_INSTALL="-full"` to install full firmware for the board. enable for UEFI.
- don't rely on KERNELSOURCE for firmware-related decisions. introduce `INSTALL_ARMBIAN_FIRMWARE` which defaults to `yes`
- rpi4b/flash-kernel: disable Armbian firmware; we need linux-firmware-raspi2, which conflicts.
Signed-off-by: Ricardo Pardini <ricardo@pardini.net>
* extensions: log to /${LOG_SUBPATH}/ instead of fixed /debug/
Signed-off-by: Ricardo Pardini <ricardo@pardini.net>
* extensions: introduce cleanup_extension_manager() called by build-all-ng's unset_all()
- to reset/unset everything done by the the initializer, so build can run again
Signed-off-by: Ricardo Pardini <ricardo@pardini.net>
* extensions: remove 'global' logging, for use with build_all_ng
- enable_extensions() will have to live on without logging to file. it's just too early.
- now init EXTENSION_MANAGER_TMP_DIR in initialize_extension_manager()
- now init EXTENSION_MANAGER_LOG_FILE in initialize_extension_manager()
Signed-off-by: Ricardo Pardini <ricardo@pardini.net>
* extensions: build-all-ng.sh bugfix due to extension's debug to stdout
- extensions (among other things) can produce output to stdout when activated
- fix: check_hash() produced "idential" (sic, now changed to IDENTICAL) to stdout as a trigger
- debugging output got mixed with "idential", rendering hash cache void for families that used extensions
- eg: sunxi, others
- fix is to send stdout to the bitbucket when sourcing the board & arch config files
- proper fix would be stop using stdout in this case and use return code for check_hash()
- one day soon
Signed-off-by: Ricardo Pardini <ricardo@pardini.net>
* Add CI build targets
Co-authored-by: Igor Pecovnik <igor.pecovnik@gmail.com>
Co-authored-by: The-going <48602507+The-going@users.noreply.github.com>
- starting from Home Assistant OS (HASSOS) setup/patchset, which is stable with pure-mainline
- *huge thanks* to Stefan Agner (@agners) from Home Assistant for his work and help with this
- CONFIG_DRM_MESON=y fixes the order of shutdown callbacks, allowing it to reboot without patches
- this increases the kernel size a bit, due to some dependencies like DRM=y
- remove the shutdown revert patch, allowing other meson64 boards to mainline-reboot
- add fdt/no-map patch fixing the dreaded "SError Interrupt on CPU4" panics that plagued the N2
- move the N2 to mainline u-boot on current (rebased, already done)
- add SPI-enabling DTB variants, which allow writing to SPI NOR flash (and usage instructions in comments)
- add UBOOT_TARGET_MAP and write_uboot_platform_mtd to current, for nand-sata-install to SPI/USB goodness
- remove the UHS-enabling patch, to avoid 1.8v vs 3.3v mess. Make sure to use only A1-rated SD cards as recommended.
- change default cpufreq governor for 24h+ stability
- other patch cleanups:
- move deprecated/non-applying patch to need-check
- remove the HardKernel ODROID-specific reboot driver and DTS patches (odroid-reboot.c) which are now useless.
- remove documentation-only patches (we have enough patches in meson64 without those)
- remove duplicated SAR ADC patches
- remove multiple different and conflicting patches for DTS and emulated-PWM GPIO fan
- now using simple on/off GPIO fan at 30 celsius, unrelated to passive cooling
* add workaround against default MAC Address (userland utility bdaddr does not work to set MAC Address as expected)
* enable bits for xt-q8l-v10 board (ap6330/bcm4330 part), switching AP6330 bluetooth to btbcm driver using serdev
facilities to avoid userspace machinery with deprecated hciattach tool, added bits to enable driver support in kernel.
Removed ap6330 bluetooth service from bsp packages, added initramfs-tools hook to include bcm4330b1.hcd firmware in initramfs
* Bumping EDGE kernel to 5.14.y
Meson64:
- removing Odroid reboot shutdown patch since its probably not needed anymore
Rockchip64:
- removing Rockpi S. No interest to maintain this any further
- removing PBP suspend. Doesn’t align. Need inspection if some other way was mainstreamed
- temporally removing Orangepi R1
* Re-adding rockpis, pbp suspend, HFLPS170 wifi and cleanup
* Removing deprecated patch, fixing ap6256 wifi
* Re-enable Opi R1 plus, untest
* Add and fix Radxa Zero
* Upgrading sunxi and sunxi64 EDGE to 5.13
Both variants tested for building
* Bump imx6 to 5.13.y
Tested
* Bump Jetson nano kernel to 5.13.y
* Move mvebu and mvebu64 edge to 5.13.y
* add DFI driver to provide hardware-based memory controller load
* adapted DRAM Memory Controller driver from rk3328, add necessary headers
* provide device tree overlays to enable DDR3 clock scaling
* adapted rk322x-box to allow DDR speed bin selection to user
* add ipb900 board gpio configuration
* add rtl8723cs driver to linux-current kernel
* use ddrbin v1.10 set to 330 Mhz at boot
* provide overlays for ddr3 at 330, 528, 660 and 800 mhz
* split emmc overlays to enable options by user choice
* modified rk322x-config to support dmc, emmc overlays
* remove optee trust os in favor of rockchip proprietary blob
for dmc functionality
* [ Rockchip64 ] Add Tinker Board 2
Using Mainline ATF/U-boot/Kernel
What works:
- USB (NOT TYPE C)
- PCIe
- LED's
- Ethernet
- HDMI
TODO:
- Type-C (fusb302 stuff)
- Type-C DP
- Regulators for big cores and GPU (sitting at default values now, no DVFS)
- Formware/driver for RTL8822CE
U-boot spits out some trash right after handing off control from SPL to U-Boot,
but doesn't impact boot. Needs looked at.
* [ rockchip64 ] remove unrelated changes to 369ab2decdc5a3c49973d8eeb783c95558dcc41a
* [ rockchip64 ] fix merge mess from symlinks step 1
* [ rockchip64 ] fix merge mess from symlinks step 2
* [ rockchip64 ] fix merge mess from symlinks step 3
* [ rockchip64 ] add asus driver for FAN53200 regulator
* Rename tinkerboard.conf to tinkerboard.wip
set as WIP for merge to trunk. Not ready for images just yet.
* revert rename to wip
wrong tinkerboard
* Rename tinkerboard-2.conf to tinkerboard-2.wip
prepare for merge to trunk. Not ready for images
* Tinker Board 2 GPU and Type-C
Support USB3 over type-C connector. display Port is still non-functional, framework in device tree however
Enable GPU
* Tinkerboard 2 DTS tweaks
Added this round:
Type-C DP now works
thermal sensors enabled (oops)
* Tinker Board 2 update config
-Adds wifi support for the RTL8822
* Updated kernel/u-boot for MCIMX7SABRE board
Supporing 'current' and 'legacy' branches for MCIMX7SABRE board
current branch:
u-boot: imx_v2020.04_5.4.70_2.3.0
kernel: imx_5.4.70_2.3.0
legacy branch:
u-boot: imx_v2018.03_4.14.98_2.0.0_ga
kernel: imx_4.14.98_2.0.0_ga
* Update kernel config with few additional options like zram, bonding, ... just a few to keep minimum consistency over kernels.
* Fixed u-boot script and kernel config for i.MX7D
Fixed bug in u-boot script preventing to use armbianEnv.txt
Configured SDMA as module to fix loading SDMA firmware
Co-authored-by: Igor Pecovnik <igor.pecovnik@gmail.com>
* remove obsolete and broken patch for pine64so u-boot
This prevents the image from being built.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
* sunxi: fix pine64so phy-mode and add yt8511 support
Pine A64-LTS board should have RGMII-TXID mode instead of RGMII-ID (the
Realtek PHY chip's RXID is sometimes broken).
In addition, new Pine A64-LTS v2 board will use YT8511 instead of
RTL8211E, which still works under RGMII-TXID mode.
Backport YT8511 driver and phy-mode change from linux-next.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Co-authored-by: Igor Pečovnik <igorpecovnik@users.noreply.github.com>
* Updated kernel/u-boot for MCIMX7SABRE board
Supporing 'current' and 'legacy' branches for MCIMX7SABRE board
current branch:
u-boot: imx_v2020.04_5.4.70_2.3.0
kernel: imx_5.4.70_2.3.0
legacy branch:
u-boot: imx_v2018.03_4.14.98_2.0.0_ga
kernel: imx_4.14.98_2.0.0_ga
* Update kernel config with few additional options like zram, bonding, ... just a few to keep minimum consistency over kernels.
Co-authored-by: Igor Pecovnik <igor.pecovnik@gmail.com>
* Add ZRAM and few other networking related options to Jetson nano legacy kernel config
* Enable legacy desktop build for jetson-nano
* Enable nightly legacy kernel build
* space
* Move Jetson patches to right location, add upstream patch
Also add upstream patch for sunxi
* Add upstream patches for Odroidxu4 current
* Add meson64 upstream patches
* Enable Virtual qemu build targets
* Bugfix - saving build number is being overwritten before saved
* Remove stable builds, not needed
* Update kernel config, enable current instead of edge
* Bump imx6 edge to 5.12.y
* Bump odroid xu4 edge to 5.12.y
* Bump Jetson nano edge to 5.12.y
* WIP: Bump sunxi to 5.12.y
- create a copy of patches and make a new link
- wireless patches needs adjutement to 5.12
- some patches are still failing
* Adjust wireless patches to build on 5.12.y
* Remove template wireless patch
* Move Espressobin edge to 5.12.y
* Bump mvebu to 5.12
- patch 92-mvebu-gpio-remove-hardcoded-timer-assignment.patch was disabled @heisath
- adjusted wireless driver for 8723ds
* Adjust sunxi / sunxi64 edge to compile
* Fix kernel config for Jetson nano edge
* bump meson64 to 5.12.y
* bump rockchip edge to 5.12.y
* Bump rockchip64 to 5.12.y
* Bump rk322x edge to 5.12.y
@paolosabatino
* Cleanup im6, re-add 5.10.y patches since one is missing in 5.12.y
* Update odroidxu4 edge links
* rk322x: moved rk322x-edge to kernel 5.12, fix overlay compilation, retouched included kernel modules
* Cleanup: remove deprecated config
Co-authored-by: Paolo Sabatino <paolo.sabatino@gmail.com>
Adds Xilinx Bootgen tools to build environment (alongside sunxi-tools, etc ..)
Adds new SoC family Zynq (7000 series, not MP/UltraScale)
Adds new board Avnet MicroZed
* enable usbip and usbip vhci-hcd as module to all devices
Add USBIP and it's module as a kernel module to all devices.
It's pretty standard package available in all other distros, allow usage of USB over IP of devices.
new file: config/kernel/linux-generic.config
modified: config/kernel/linux-odroidxu4-legacy.config
modified: lib/compilation.sh
* enable usbip and usbip vhci-hcd as module to devices
* rm unused config file
Co-authored-by: lededev <lededev@noreplay.github.com>
* add device tree overlays to handle boards with power regulation issues,
* fix misconfiguration issues in overlays
* add missing wireguard module for rk322x-current and -edge
* add Jetson Nano
* Update jetson-nano.conf
* Update targets.conf
* Add better description
* Adjust config - try to enable ZRAM
* Packaging patch not needed
* Extlinux was solved in other commit
* Move board to CSC for now
Co-authored-by: Igor Pečovnik <igorpecovnik@users.noreply.github.com>
Co-authored-by: Igor Pecovnik <igor.pecovnik@gmail.com>
- Enabled nfc on rk322x-dev and disable on rk322x-current (need further development)
- Tidied up rk322x-current device tree
- enabled nfc rockchip driver enabled in rk322x-dev kernel config
- Enabled EHCI controller in u-boot (added patch for inno-phy, device tree and config bits), better device detection for dwc2 usb otg port
- Removed SPL_FIT_GENERATOR from u-boot configuration, fixed .its file to use binman
- fixed rk322x its file (now includes dtb), reverted u-boot to v2020.10 and changed dev_* into log_debug() calls
* Bump rockchip DEV 32b to 5.11.y
* Move mvebu64 DEV to 5.11.y
* Move Rockchip64 DEV to 5.11.y
Disabling general-rkvdec_nv15.patch - need more attention
* Add Meson DEV / Odroid C1
* Move OdroidXU4 DEV to tobetter's 5.11.y branch
* Bump sunxi DEV to 5.11.y
* Bump mvebu DEV to 5.11.y
* Enable RTC (hym8563) for Station P1 in mainline (renaming DT in process)
* Switch Station P1 to rockchip64
* Fix linking for Station P1 device tree in legacy
`CONFIG_RTL8188EU` seem no longer exist in config. Unable to find in menuconfig. Therefore removed.
@ThomasKaiser FYI: `CONFIG_CRYPTO_ZSTD` has been forced to `y` by `ZSWAP_COMPRESSOR_DEFAULT_ZSTD [=y] && <choice>`
Standard firewall features were introduced in
6a165742e8 but then removed in
6788786057. This commit restores them and also
adds support for the tc-mirred action.
* [rockchip64-current] add gamepad and joystick support
Added modules similar to rockchip64-legacy
* [meson{64}-current] add gamepad and joystick support
* [gitignore] temp vim files
* [sunxi{64}-current] add gamepad and joystick support
* [mvebu{64}-current] add gamepad and joystick support
* [misc dev] add gamepad and joystick support
* [meson and sunxi legacy] add gamepad and joystick support
* [misc legacy] add gamepad and joystick support
- curently attached to RC7 as https://github.com/armbian/build/pull/2378
- config derived from current and contains all latest changes
- dirty reboot and eth0 reset hacks are not added and can be added later if still needed (need_check subfolder)
