- Add mainline device tree for YY3588 board
- Enable all peripherals: USB 3.0, Ethernet, PCIe, HDMI
- Add RK8602 PMIC regulators for CPU/NPU power
- Enable I2C buses for PMIC and RTC
- Fix pinctrl conflicts (I2C1 M2, disable SFC for UART7)
- Configure USB-C and USB 3.0 host ports
- Add HDMI0 output with HDPTX PHY
- Enable thermal management with PWM fan
- Add SD card and eMMC storage support
- Configure all UARTs, I2S audio, and SPI buses
- ES8323 audio codec currently disabled for further debugging
- no need for vendor u-boot, as mainline can boot vendor kernel fine
- update comments with hardware pin references
- mainline boot order: NVMe -> USB -> eMMC
- boot order: NVMe -> MMC
- GMAC works
- nvme works
- `ums` et al working
- usb3 ports (on carrier board) work
- DT is copy (not symlink) from kernel DT due to NPU nodes
- vendor:
- kernel: armbian/linux-rockchip already had a DTS from jriek
- u-boot: taken from jriek (reorg'ed the defconfig)
- edge:
- kernel: taken from jriek's 6.11 wip branch
- u-boot: generic (can only boot SD/eMMC)
Switch to NO_HZ_IDLE for energy saving. Also enable Menu cpuidle
governor for tickless systems.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Signed-off-by: Igor Pecovnik <igor@armbian.com>
> merry everything and a happy always
- mainline:
- enable "edge" branch, with custom DT
- works: almost everything
- does NOT work:
- USB-C port is only for OTG/UMS (NOT USB3-host) - didn't describe fusb302 et al in DT
- any of the 3x HDMI -> MIPI (or whatever) HDMI-In's (thus this is a 1x1, not 4x1)
- front USB3 blue ports are actually USB2 (also in vendor kernel)
- front USB2 black ports don't work (but are powered)
- Analog audio - didn't describe, could be, but I've no way to test
- use mainline u-boot v2026.01-rc5 (with custom DT/defconfig/etc) with mainline ATF
- boot order: SD -> NVMe -> USB -> eMMC -> ETH
- adapt usage of shared "mekotronics" vendor include only for vendor/legacy
- also fix DTB: `rockchip/rk3588-blueberry-r58-4x4.dtb` for vendor
- same across vendor and mainline
- mainline u-boot kinda-boots vendor kernel, but TF-A mismatch ref HDMI-rx
- so use vendor u-boot and rk blob for vendor branch/kernel
- straight-ish from vendor (which is a complete mess)
- front:
- blue ports work (in usb2.0 mode, which also happens in vendor kernel)
- black ports do NOT work (but are powered...?)
- back:
- white ports work in usb 2.0 mode (as expected, also in vendor kernel)
- those ports have too-long wires (flat cable) and reset all the time
- in summary: blue "USB3" ports at the front work in USB2.0 mode
- rest doesn't
- also enable CONFIG_ROCKCHIP_MASKROM_IMAGE for quick development
- fix conflicting vendor hook
- only hack the vendor u-boot down to next-dev-v2024.03 for vendor/legacy
* fix(rootfs): pass GIT_FIXED_WORKDIR inline to fetch_from_repo
Instead of using 'export GIT_FIXED_WORKDIR' and then 'unset' after,
pass the variable inline to the fetch_from_repo call. This ensures
the variable only exists in the context of that specific command
and doesn't leak into subsequent calls.
This follows the same pattern used in uboot-git.sh and kernel-git.sh.
---------
Co-authored-by: Viacheslav Bocharov <adeep@lexina.in>
- Remove redundant daily cron schedule (already runs on push to main)
- Add concurrency control to cancel old runs
- Improve formatting and add clarifying comments
- Add push trigger for main branch
