* Bugfix - Bananapi PRO seems to work fine with latest u-boot
Done many reboots and it didn't break. The same has to be tested with other A20 boards
* Set Allwinner 32bit hw to most recent u-boot 2021.07
* Let's move all to 2021.07 and test ...
* remove obsolete and broken patch for pine64so u-boot
This prevents the image from being built.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
* sunxi: fix pine64so phy-mode and add yt8511 support
Pine A64-LTS board should have RGMII-TXID mode instead of RGMII-ID (the
Realtek PHY chip's RXID is sometimes broken).
In addition, new Pine A64-LTS v2 board will use YT8511 instead of
RTL8211E, which still works under RGMII-TXID mode.
Backport YT8511 driver and phy-mode change from linux-next.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Co-authored-by: Igor Pečovnik <igorpecovnik@users.noreply.github.com>
* Remove unnecessary patch
- this patch works when compiling and installing manually.
- the dtb with the changes is taken from the kernel and not from u-boot, therefore this patch does not work.
* Add enable-audio-codec-bpim2ultra-kernel.patch
- Add patch to enable audio codec in bpi-m2-ultra with h3 compatible
- Built and tested on Armbian Buster with Kernel 5.11.x (edge)
* Remove unnecessary patch
- this patch works when compiling and installing manually.
- the dtb with the changes is taken from the kernel and not from u-boot, therefore this patch does not work.
* Add enable-sound-pinecube-kernel.patch
- Add patch to enable audio codec in pinecube with v3s compatible
- Built and tested on Armbian Buster with Kernel 5.11.x (edge)
* sunxi: kernel: current/dev: enable sun6i-csi and disable LL debug on UART0
The former is useful on some boards, e.g. PineCube.
The latter blocks boards that do not utilize UART0 from booting.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
* sunxi: add new family sun8i-v3s
This family is intended for boards with V3/V3s/S3/S3L chips and low
DRAM capacity.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
* sunxi: add PineCube board
This board features Sochip S3 SoC (Allwinner V3 die + co-packaged 128MiB
DRAM), and an OmniVision OV5640 camera is shipped with the board.
Add support for it. It could be used as an IP camera then.
Kernel support is only added to current/dev branch, with dev just using
mainline-merged DT and current using backported DT from 5.10-rc.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
* sunxi: kernel: current/dev: add V3s OHCI/EHCI nodes
These are needed for USB host on V3s boards to work.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
* Disable DE2 in u-boot to improve EDID detection
* Remove deprecated patches
* Define BOOTBRANCH in top level
Signed-off-by: Igor Pecovnik <igor.pecovnik@gmail.com>
* Sunvell R69: cpu voltage regulator (re-)added - dram clock reduced.
CPU regulator (re-)added to u-boot and kernel dts - the box will not boot without it.
Dram clock reduced in defconfig to increase stability.
[AR-85]
* Fix wifi
patch "board-h2plus-nanopi-duo-add-device.patch": increase post-power-on-delay-ms from 50ms to 200ms in wifi_pwrseq node in nanopi-duo dts [dev-branch].
Change in line with other XRADIO device trees (orange pi zero, sunvell).
See also Pull Request #1605.
* Fix xradio patch (dev-branch)
fix KConfig to 5.x - WLAN_VENDOR-flag set to "y" in line with other drivers - otherwise module not loaded.
* correct device name
change nodes "model" and "compatible" to correct device name (from "NanoPi Duo AIR" to "NanoPi Duo") [dev-branch]
Not functionally necessary, but more correct.
* Initial commit for serial consoles rfc
* Board configuration cleanup + small tweaks
* Add serial gadget rename to dev kernel as well
* Cleanup, fixing permissions
* Cleanup board configs
* Initial commit for FA ZeroPi.
* Tested for building.
* Adjust few bugs.
* Move to WIP since its not tested on hardware yet.
Signed-off-by: Igor Pecovnik <igor.pecovnik@gmail.com>
The eMMC must have been forgotten when the device tree for the NanoPi Neo Air was being added to mainline u-boot, which results in the device being unable to boot when installed to the internal eMMC using the nand-sata-install utility.
