* DFI driver fix to let DDR3 rk322x handle DMC driver
* edge kernel: removal for Gigabit Ethernet DMA
workaround for rk3288
* reinstate CONFIG_DEBUG_FS=y with both current/edge kernels
* Modify radxa-e54c board config to fix leds, network and Gnome
Modify led setup section to use new led device names
Add a keyfile /etc/NetworkManager/conf.d/99-unmanaged-devices.conf to set the internal ethernet, end1, used to connect to the internal switch chip to unmanaged. This interface doesn't accept dhcp IP addresses and Network Manager attempts to connect it via dhcp causing errors.
A vendor kernel build with Gnome desktop attempts to use Wayland unsuccessfully causing the desktop to take over 10 minutes to initialise eventually using X11. Modify the board /usr/lib/armbian/armbian-firstlogin file to set WaylandEnable = false if the build is for a vendor kernel with a Gnome desktop.
* Update config/boards/radxa-e54c.conf
Tested the suggestion and it works.
Co-authored-by: coderabbitai[bot] <136622811+coderabbitai[bot]@users.noreply.github.com>
* Removing the RedHat-specific plugin
---------
Co-authored-by: coderabbitai[bot] <136622811+coderabbitai[bot]@users.noreply.github.com>
- Add mainline device tree for YY3588 board
- Enable all peripherals: USB 3.0, Ethernet, PCIe, HDMI
- Add RK8602 PMIC regulators for CPU/NPU power
- Enable I2C buses for PMIC and RTC
- Fix pinctrl conflicts (I2C1 M2, disable SFC for UART7)
- Configure USB-C and USB 3.0 host ports
- Add HDMI0 output with HDPTX PHY
- Enable thermal management with PWM fan
- Add SD card and eMMC storage support
- Configure all UARTs, I2S audio, and SPI buses
- ES8323 audio codec currently disabled for further debugging
- no need for vendor u-boot, as mainline can boot vendor kernel fine
- update comments with hardware pin references
- mainline boot order: NVMe -> USB -> eMMC
- boot order: NVMe -> MMC
- GMAC works
- nvme works
- `ums` et al working
- usb3 ports (on carrier board) work
- DT is copy (not symlink) from kernel DT due to NPU nodes
- vendor:
- kernel: armbian/linux-rockchip already had a DTS from jriek
- u-boot: taken from jriek (reorg'ed the defconfig)
- edge:
- kernel: taken from jriek's 6.11 wip branch
- u-boot: generic (can only boot SD/eMMC)
Switch to NO_HZ_IDLE for energy saving. Also enable Menu cpuidle
governor for tickless systems.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Signed-off-by: Igor Pecovnik <igor@armbian.com>
> merry everything and a happy always
- mainline:
- enable "edge" branch, with custom DT
- works: almost everything
- does NOT work:
- USB-C port is only for OTG/UMS (NOT USB3-host) - didn't describe fusb302 et al in DT
- any of the 3x HDMI -> MIPI (or whatever) HDMI-In's (thus this is a 1x1, not 4x1)
- front USB3 blue ports are actually USB2 (also in vendor kernel)
- front USB2 black ports don't work (but are powered)
- Analog audio - didn't describe, could be, but I've no way to test
- use mainline u-boot v2026.01-rc5 (with custom DT/defconfig/etc) with mainline ATF
- boot order: SD -> NVMe -> USB -> eMMC -> ETH
- adapt usage of shared "mekotronics" vendor include only for vendor/legacy
- also fix DTB: `rockchip/rk3588-blueberry-r58-4x4.dtb` for vendor
- same across vendor and mainline
- mainline u-boot kinda-boots vendor kernel, but TF-A mismatch ref HDMI-rx
- so use vendor u-boot and rk blob for vendor branch/kernel
- also enable CONFIG_ROCKCHIP_MASKROM_IMAGE for quick development
- fix conflicting vendor hook
- only hack the vendor u-boot down to next-dev-v2024.03 for vendor/legacy
