* add device tree overlays to handle boards with power regulation issues,
* fix misconfiguration issues in overlays
* add missing wireguard module for rk322x-current and -edge
* add Jetson Nano
* Update jetson-nano.conf
* Update targets.conf
* Add better description
* Adjust config - try to enable ZRAM
* Packaging patch not needed
* Extlinux was solved in other commit
* Move board to CSC for now
Co-authored-by: Igor Pečovnik <igorpecovnik@users.noreply.github.com>
Co-authored-by: Igor Pecovnik <igor.pecovnik@gmail.com>
- Enabled nfc on rk322x-dev and disable on rk322x-current (need further development)
- Tidied up rk322x-current device tree
- enabled nfc rockchip driver enabled in rk322x-dev kernel config
- Enabled EHCI controller in u-boot (added patch for inno-phy, device tree and config bits), better device detection for dwc2 usb otg port
- Removed SPL_FIT_GENERATOR from u-boot configuration, fixed .its file to use binman
- fixed rk322x its file (now includes dtb), reverted u-boot to v2020.10 and changed dev_* into log_debug() calls
* Bump rockchip DEV 32b to 5.11.y
* Move mvebu64 DEV to 5.11.y
* Move Rockchip64 DEV to 5.11.y
Disabling general-rkvdec_nv15.patch - need more attention
* Add Meson DEV / Odroid C1
* Move OdroidXU4 DEV to tobetter's 5.11.y branch
* Bump sunxi DEV to 5.11.y
* Bump mvebu DEV to 5.11.y
* Enable RTC (hym8563) for Station P1 in mainline (renaming DT in process)
* Switch Station P1 to rockchip64
* Fix linking for Station P1 device tree in legacy
`CONFIG_RTL8188EU` seem no longer exist in config. Unable to find in menuconfig. Therefore removed.
@ThomasKaiser FYI: `CONFIG_CRYPTO_ZSTD` has been forced to `y` by `ZSWAP_COMPRESSOR_DEFAULT_ZSTD [=y] && <choice>`
Standard firewall features were introduced in
6a165742e8 but then removed in
6788786057. This commit restores them and also
adds support for the tc-mirred action.
* [rockchip64-current] add gamepad and joystick support
Added modules similar to rockchip64-legacy
* [meson{64}-current] add gamepad and joystick support
* [gitignore] temp vim files
* [sunxi{64}-current] add gamepad and joystick support
* [mvebu{64}-current] add gamepad and joystick support
* [misc dev] add gamepad and joystick support
* [meson and sunxi legacy] add gamepad and joystick support
* [misc legacy] add gamepad and joystick support
- curently attached to RC7 as https://github.com/armbian/build/pull/2378
- config derived from current and contains all latest changes
- dirty reboot and eth0 reset hacks are not added and can be added later if still needed (need_check subfolder)
* Add WIP support for Orangepi Zero 2
* squeeze H616 patches into sunxi-dev
* Update linux-sunxi64-dev.config
* H616: Limit CPUMAX
* Enable DEV only
* H616: remove patches from sunxi-current
* H616: apply new patchset
Co-authored-by: EvilOlaf <werner@armbian.de>
Co-authored-by: Werner <EvilOlaf@users.noreply.github.com>
* sunxi: kernel: current/dev: enable sun6i-csi and disable LL debug on UART0
The former is useful on some boards, e.g. PineCube.
The latter blocks boards that do not utilize UART0 from booting.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
* sunxi: add new family sun8i-v3s
This family is intended for boards with V3/V3s/S3/S3L chips and low
DRAM capacity.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
* sunxi: add PineCube board
This board features Sochip S3 SoC (Allwinner V3 die + co-packaged 128MiB
DRAM), and an OmniVision OV5640 camera is shipped with the board.
Add support for it. It could be used as an IP camera then.
Kernel support is only added to current/dev branch, with dev just using
mainline-merged DT and current using backported DT from 5.10-rc.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
* sunxi: kernel: current/dev: add V3s OHCI/EHCI nodes
These are needed for USB host on V3s boards to work.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Although enabling this feature can have performance gain, this is
proven to be broken on new kernels and is dropped in linux-next now
in git commit 80bf194625f5.
Disable this to fix ZRAM issues and get future proof on this feature.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
- move Odroid C4 from legacy u-boot toward mainline
- get rid of dirty legacy u-boot code
- get rid of FAT boot partition
- briefly tested
- both kernels can operate with one standard boot script
- add upstream patch and adjust config
- fix console
- don't clock C4 too high by default
Without this option enabled, we will not be able to use the setcap tool to set file capabilities on a F2FS partition.
Signed-off-by: Jack Chen <redchenjs@live.com>
