* meson64: bump u-boot to 2021.07, rework patches
- as always based on chewitt's tree, with differences:
- squashed versions of HC4+SATA, Radxa Zero, DT tree sync patches
- so that DTB/config/code changes related to the same feature/board are grouped
- removed documentation changes and Makefile reordering patches
Signed-off-by: Ricardo Pardini <ricardo@pardini.net>
* meson64: ODROID HC4/N2: simplify/remove board vs family hacks; better SPI support
- thanks to mainline 2021.07 u-boot and it's HC4 config we can remove the conditionals
- boards now define the u-boot vars instead of conditionals in family
- on the HC4, build u-boot twice: one for SD (old C4 config) and one for HC4 (new SATA/SPI config)
- reason is that the HC4 version does not work very well unless it is actually booted from SPI
- meson64_common: don't override UBOOT_TARGET_MAP if board-defined
- but the default UBOOT_TARGET_MAP is still defined if the board didn't
- (sneakily) add lm-sensors fancontrol to the HC4's board packages
Signed-off-by: Ricardo Pardini <ricardo@pardini.net>
* add workaround against default MAC Address (userland utility bdaddr does not work to set MAC Address as expected)
* enable bits for xt-q8l-v10 board (ap6330/bcm4330 part), switching AP6330 bluetooth to btbcm driver using serdev
facilities to avoid userspace machinery with deprecated hciattach tool, added bits to enable driver support in kernel.
Removed ap6330 bluetooth service from bsp packages, added initramfs-tools hook to include bcm4330b1.hcd firmware in initramfs
* Bumping EDGE kernel to 5.14.y
Meson64:
- removing Odroid reboot shutdown patch since its probably not needed anymore
Rockchip64:
- removing Rockpi S. No interest to maintain this any further
- removing PBP suspend. Doesn’t align. Need inspection if some other way was mainstreamed
- temporally removing Orangepi R1
* Re-adding rockpis, pbp suspend, HFLPS170 wifi and cleanup
* Removing deprecated patch, fixing ap6256 wifi
* Re-enable Opi R1 plus, untest
* Add and fix Radxa Zero
* Add support for Radxa Zero
u-boot: new patch based on v2021.04
kernel: use patches sent to kernel list by chewitt
Tested with minimal build and cinnamon desktop:
- SD/eMMC, ok
- USB3, works in USB 2 mode
- HDMI, ok
- WiFi/BT, ok
Signed-off-by: Jack Ma <jack@radxa.com>
* Add build targets
* Cleanup and set min speed to 666000
* Change to WIP target
Support status undetermined
Co-authored-by: Jack Ma <jack@radxa.com>
- done in a single if block in sm1 family
- add nand-sata-install support via UBOOT_TARGET_MAP and write_uboot_platform_mtd
Signed-off-by: Ricardo Pardini <ricardo@pardini.net>
- fix/dup bootscript, since new u-boot fixed n2_plus to n2-plus variant
- g12b: if n2 and edge, enable new u-boot; include non-SD version as SPI binary; write_uboot_platform_mtd
- Kernel DTS patch to add SPI-flash-enabled DTBs (slower eMMC), produces -spi .dtbs for n2 and n2-plus
- This could also be an overlay, but I dunno overlays.
- SPI+USB3 boot works with "pendrive" storage, untested with cabled/high power USB->SATA or USB->NVMe
Signed-off-by: Ricardo Pardini <ricardo@pardini.net>
- We really want the u-boot.bin.sd.bin for HC4
- During VIM3L-adding commit, "odroid*c4" was replaced with "odroid-c4" and "odroid-hc4"
- Which is cool but it's actually "odroidc4" and "odroidhc4"
- Add a warning to save future time if no FIP tree decided by SM1 family
Signed-off-by: Ricardo Pardini <ricardo@pardini.net>
* bump rockchip64 ATF to 2.5
v2.5 includes our patches and some other RK3399 improvements
* Delete power domains patch
included in ATF v2.5
* Delete fix-reset-in-v2.2.patch
Included in v2.5
* disable logging patch
&console.console is causing a compile error with ATF v2.5. I haven't looked into it yet, disable for now.
* Add experimental suspend support for PBP
Co-authored-by: Igor Pecovnik <igor.pecovnik@gmail.com>
* Upgrading sunxi and sunxi64 EDGE to 5.13
Both variants tested for building
* Bump imx6 to 5.13.y
Tested
* Bump Jetson nano kernel to 5.13.y
* Move mvebu and mvebu64 edge to 5.13.y
* move pinebook tweaks
* fix dest
* Add also special keys definitions
* Clear out tech dept
* Delete prepare.sh
Co-authored-by: Igor Pečovnik <igorpecovnik@users.noreply.github.com>
* add DFI driver to provide hardware-based memory controller load
* adapted DRAM Memory Controller driver from rk3328, add necessary headers
* provide device tree overlays to enable DDR3 clock scaling
* adapted rk322x-box to allow DDR speed bin selection to user
* add ipb900 board gpio configuration
* add rtl8723cs driver to linux-current kernel
* use ddrbin v1.10 set to 330 Mhz at boot
* provide overlays for ddr3 at 330, 528, 660 and 800 mhz
* split emmc overlays to enable options by user choice
* modified rk322x-config to support dmc, emmc overlays
* remove optee trust os in favor of rockchip proprietary blob
for dmc functionality
* [ Rockchip64 ] Add Tinker Board 2
Using Mainline ATF/U-boot/Kernel
What works:
- USB (NOT TYPE C)
- PCIe
- LED's
- Ethernet
- HDMI
TODO:
- Type-C (fusb302 stuff)
- Type-C DP
- Regulators for big cores and GPU (sitting at default values now, no DVFS)
- Formware/driver for RTL8822CE
U-boot spits out some trash right after handing off control from SPL to U-Boot,
but doesn't impact boot. Needs looked at.
* [ rockchip64 ] remove unrelated changes to 369ab2decdc5a3c49973d8eeb783c95558dcc41a
* [ rockchip64 ] fix merge mess from symlinks step 1
* [ rockchip64 ] fix merge mess from symlinks step 2
* [ rockchip64 ] fix merge mess from symlinks step 3
* [ rockchip64 ] add asus driver for FAN53200 regulator
* Rename tinkerboard.conf to tinkerboard.wip
set as WIP for merge to trunk. Not ready for images just yet.
* revert rename to wip
wrong tinkerboard
* Rename tinkerboard-2.conf to tinkerboard-2.wip
prepare for merge to trunk. Not ready for images
* Tinker Board 2 GPU and Type-C
Support USB3 over type-C connector. display Port is still non-functional, framework in device tree however
Enable GPU
* Tinkerboard 2 DTS tweaks
Added this round:
Type-C DP now works
thermal sensors enabled (oops)
* Tinker Board 2 update config
-Adds wifi support for the RTL8822
* Bugfix - fancy modesetting seems to be broken on Amlogic GLX series. Reverting to fbdev fixes the problem of desktop not showing up.
* Tested on Vim2
- Armbian already had all the FIP-magic needed, just use it.
- Introduce USE_ODROID_UBOOT with a list of branches that use Odroid's 2015 u-boot
- this is mostly in preparation for non-Odroid G12B/meson64 boards (Khadas VIM3...)
- In case $BRANCH is listed in USE_ODROID_UBOOT:
- use BOOTCONFIG_ODROID and BOOTSCRIPT_ODROID from board.conf
- build 2015 u-boot just like before
- Small hack into boot-meson64.cmd to handle u-boot vs kernel: n2_plus vs n2-plus DTB/FDT naming mismatch
- overrides the default $fdtfile based on $variant
- armbianEnv still has final say if $fdtfile is set there (it isn't for n2/n2plus)
- Extra:
- remove unused n2-mainline bootscript (maybe from a previous try?)
- comments about FIP trees being identical across N2/N2Plus and C4/HC4 families so no future time wastage
- only set CPUMIN/CPUMAX/GOVERNOR in meson64_common.inc if not already set by the board.conf
- Add some ${bootargs} debugging to mainline/default boot-meson64.cmd
Signed-off-by: Ricardo Pardini <ricardo@pardini.net>
* cleanup add vim3l
* Add Khadas edge config
* Add Khadas edge sources definitions. It boots
* Change configuration to maximised model
* Adjust build configs
* witch to case statement for meson x11 config
* push vim1 naming
* Booting VIM2 with khadas prebuild u-boot
Can load from an empty eMMC, can be installed to eMMC via nand-sata-install
* Add Vim1 and move 1 and 2 to supported. VIM1 is not tested yet.
* Enable full featured desktop with 3D for khadas vim 1 and vim2
* Update meson64_common.inc
Co-authored-by: Igor Pecovnik <igor.pecovnik@gmail.com>
* Move function run_on_sdcard to more appropriate location
* Focus on bash headers, unify, adjust (c)
* Adjust (c) to range
* Cleanup compile.sh
* Cleaning main
* Build all, main configs
* fine tunning
* Improve readme
* Remove Docker version check from compile.sh since its deprecated
* Remove meta package creation which was needed for upgrade
* Update in-code documentation
* Bugfix
* Making oneliner
* Remove Groovy debug leftovers
* Add readme to distributions
* Update
* More text adjust
* Add virtual
* add more
* Updated kernel/u-boot for MCIMX7SABRE board
Supporing 'current' and 'legacy' branches for MCIMX7SABRE board
current branch:
u-boot: imx_v2020.04_5.4.70_2.3.0
kernel: imx_5.4.70_2.3.0
legacy branch:
u-boot: imx_v2018.03_4.14.98_2.0.0_ga
kernel: imx_4.14.98_2.0.0_ga
* Update kernel config with few additional options like zram, bonding, ... just a few to keep minimum consistency over kernels.
Co-authored-by: Igor Pecovnik <igor.pecovnik@gmail.com>
