- starting from Home Assistant OS (HASSOS) setup/patchset, which is stable with pure-mainline
- *huge thanks* to Stefan Agner (@agners) from Home Assistant for his work and help with this
- CONFIG_DRM_MESON=y fixes the order of shutdown callbacks, allowing it to reboot without patches
- this increases the kernel size a bit, due to some dependencies like DRM=y
- remove the shutdown revert patch, allowing other meson64 boards to mainline-reboot
- add fdt/no-map patch fixing the dreaded "SError Interrupt on CPU4" panics that plagued the N2
- move the N2 to mainline u-boot on current (rebased, already done)
- add SPI-enabling DTB variants, which allow writing to SPI NOR flash (and usage instructions in comments)
- add UBOOT_TARGET_MAP and write_uboot_platform_mtd to current, for nand-sata-install to SPI/USB goodness
- remove the UHS-enabling patch, to avoid 1.8v vs 3.3v mess. Make sure to use only A1-rated SD cards as recommended.
- change default cpufreq governor for 24h+ stability
- other patch cleanups:
- move deprecated/non-applying patch to need-check
- remove the HardKernel ODROID-specific reboot driver and DTS patches (odroid-reboot.c) which are now useless.
- remove documentation-only patches (we have enough patches in meson64 without those)
- remove duplicated SAR ADC patches
- remove multiple different and conflicting patches for DTS and emulated-PWM GPIO fan
- now using simple on/off GPIO fan at 30 celsius, unrelated to passive cooling
* add workaround against default MAC Address (userland utility bdaddr does not work to set MAC Address as expected)
* enable bits for xt-q8l-v10 board (ap6330/bcm4330 part), switching AP6330 bluetooth to btbcm driver using serdev
facilities to avoid userspace machinery with deprecated hciattach tool, added bits to enable driver support in kernel.
Removed ap6330 bluetooth service from bsp packages, added initramfs-tools hook to include bcm4330b1.hcd firmware in initramfs
* Bumping EDGE kernel to 5.14.y
Meson64:
- removing Odroid reboot shutdown patch since its probably not needed anymore
Rockchip64:
- removing Rockpi S. No interest to maintain this any further
- removing PBP suspend. Doesn’t align. Need inspection if some other way was mainstreamed
- temporally removing Orangepi R1
* Re-adding rockpis, pbp suspend, HFLPS170 wifi and cleanup
* Removing deprecated patch, fixing ap6256 wifi
* Re-enable Opi R1 plus, untest
* Add and fix Radxa Zero
* Upgrading sunxi and sunxi64 EDGE to 5.13
Both variants tested for building
* Bump imx6 to 5.13.y
Tested
* Bump Jetson nano kernel to 5.13.y
* Move mvebu and mvebu64 edge to 5.13.y
* add DFI driver to provide hardware-based memory controller load
* adapted DRAM Memory Controller driver from rk3328, add necessary headers
* provide device tree overlays to enable DDR3 clock scaling
* adapted rk322x-box to allow DDR speed bin selection to user
* add ipb900 board gpio configuration
* add rtl8723cs driver to linux-current kernel
* use ddrbin v1.10 set to 330 Mhz at boot
* provide overlays for ddr3 at 330, 528, 660 and 800 mhz
* split emmc overlays to enable options by user choice
* modified rk322x-config to support dmc, emmc overlays
* remove optee trust os in favor of rockchip proprietary blob
for dmc functionality
* [ Rockchip64 ] Add Tinker Board 2
Using Mainline ATF/U-boot/Kernel
What works:
- USB (NOT TYPE C)
- PCIe
- LED's
- Ethernet
- HDMI
TODO:
- Type-C (fusb302 stuff)
- Type-C DP
- Regulators for big cores and GPU (sitting at default values now, no DVFS)
- Formware/driver for RTL8822CE
U-boot spits out some trash right after handing off control from SPL to U-Boot,
but doesn't impact boot. Needs looked at.
* [ rockchip64 ] remove unrelated changes to 369ab2decdc5a3c49973d8eeb783c95558dcc41a
* [ rockchip64 ] fix merge mess from symlinks step 1
* [ rockchip64 ] fix merge mess from symlinks step 2
* [ rockchip64 ] fix merge mess from symlinks step 3
* [ rockchip64 ] add asus driver for FAN53200 regulator
* Rename tinkerboard.conf to tinkerboard.wip
set as WIP for merge to trunk. Not ready for images just yet.
* revert rename to wip
wrong tinkerboard
* Rename tinkerboard-2.conf to tinkerboard-2.wip
prepare for merge to trunk. Not ready for images
* Tinker Board 2 GPU and Type-C
Support USB3 over type-C connector. display Port is still non-functional, framework in device tree however
Enable GPU
* Tinkerboard 2 DTS tweaks
Added this round:
Type-C DP now works
thermal sensors enabled (oops)
* Tinker Board 2 update config
-Adds wifi support for the RTL8822
