On v2025.01 and v2025.04 I get the following error
starting USB...
Bus usb@ff500000: dwc3_meson_gxl_get_phys: usb2 ports: 1
probe failed, error -114
No USB controllers found
So revert back to v2024.10 until sorted.
Signed-off-by: Patrick Yavitz <pyavitz@gmail.com>
- **CHANGE**: This version tries to boot SD first (thus SD -> USB -> NVMe -> eMMC); before it would boot USB before SD
- as Armbian u-boot is possibly deployed to SPI, try to make as compatible as possible; eg enable squashfs support
- enable `setexpr` and `fileenv`, used by HAOS
- HAOS already has support for booting VIM3 from NVMe: https://github.com/home-assistant/operating-system/pull/3784
- borrowed `fileenv` patch from v2025.01 to .04
- Similar treatment that `odroidm1` got in https://github.com/armbian/build/pull/7769
- note: I will be leaving my VIM3 behind in the other side of the globe, so this is my last chance to test
- Fix dram, mmc for h616.
- The prefix is missing if we use OF_UPSTREAM
- upstream: arm64: sun50i-h616: sync with sunxi-6.12 kernel
- upstream: arm64: Add sun50i-h618-bananapi-m4-berry.dts
* Create rk3588-orangepi-5-ultra.dts
* Create orangepi5-ultra.csc
* fixups
* add notes
* fix u-boot compilation
* Update to v7 patch series
https://patchwork.kernel.org/project/linux-arm-kernel/cover/20250222193332.1761-1-honyuenkwun@gmail.com/
* Update rk3588-orangepi-5-ultra.dts
While I don't fully understand either the `kernel-dtb` command nor the dt syntax itself for some reason the `nophandles` version stripped more than actually phandles. Lets see what happens this way.
* Delete patch/kernel/integrate-6.15/0001-tools-Makefile-remove-pci-target.patch
* disable OPTEE
c81f89ca90
- as Armbian u-boot is possibly deployed to SPI (replacing Petitboot),
try to make as compatible as possible; eg enable squashfs support
- in this case, `setexpr` and `fileenv` are used by HAOS
- found `fileenv` here 049e1a1949
Signed-off-by: Ricardo Pardini <ricardo@pardini.net>
Follow change from radxa 738cda44532c324e07296c95751e3083fa95f282.
Change with command:
sed -i "/CONFIG_OPTEE/d" patch/u-boot/legacy/u-boot-radxa-rk35xx/defconfig/*
Contains rewritten dts, based on decompiled dtb from original Klipad50
(as similiar as possible to original).
Kernel defconfig taken from MKSPI (replaced "mkspi" with "mksklipad50")
* add nanopi-r3s.csc board config
* Nanopi R3S - add uboot patch
* Nanopi R3S - add dts
* fix bogus patch header
* Migrate to new patch series
Source & credits https://patchwork.ozlabs.org/project/uboot/list/?series=438193
I still need to figure out how to convert a patch series from patchwork in a way so the build framework doesn't complain about headers and magic and whatever. So a few hundreds of header lines have been replaced with something generic.
Applies and builds fine now against current stable v2024.10
* Create board-nanopi-r3s-fix-leds.patch
Thx https://github.com/armbian/build/pull/7556#issuecomment-2615110100
* Rename board-nanopi-r3s-fix-leds.patch to xx-board-nanopi-r3s-fix-leds.patch
* add new patch
- also LEDs, networking, more supported compression methods...
- copypasta reigns supreme. refactor is coming, just not today
- also hack the u-boot dtsi for consistent-with-Linux-mainline-DT mmc/sd numbering
- this was previously a separate patch in 2024.10
* Correcting the Perf unit's interrupt source number to 66 as stated in the Allwinner A10User manual to resolve conflict with Uart 2 which actually uses interrupt source number 3
* rename to all lower case and add in sun4i-emac dma support. Note that support only exist in the driver for the rx channel
* Ensure that sun4i patches actually implemented
Signed-off-by: Ryan L <ryestar101@gmail.com>
* Apply performance monitoring unit IRQ number patch to uboot
* Add patch for resolving the perf unit irq number to the edge kernel
Signed-off-by: Ryan L <ryestar101@gmail.com>
* Add sun4i emac ethernet DMA support to the edge kernel
Signed-off-by: Ryan L <ryestar101@gmail.com>
* Append missing .patch so that our patch is found and works properly
Signed-off-by: Ryan L <ryestar101@gmail.com>
* Apply EMAC DMA support and PMU fix to edge kernel
---------
Signed-off-by: Ryan L <ryestar101@gmail.com>
* rockchip64: add `BOOT_SCENARIO=binman` for mainline u-boot
- drop special handling for 3308's `legacy` branch
- rpardini: note how SPI/mtd is not yet supported for this scenario
Co-authored-by: Ricardo Pardini <ricardo@pardini.net> (squash/splits, shellfmt)
* `rock-s0`/`rockpi-s`: use `BOOT_SCENARIO=binman`; move blobs to armbian/rkbin
- Move rk3308 boot blobs to armbian/rkbin
- delete obsolete ones
- Alter rock-s0 and rockpi-s to use the new "binman" BOOT_SCENARIO
Co-authored-by: Ricardo Pardini <ricardo@pardini.net> (shellfmt; small fixes; squashes)
- Bump U-Boot from v2024.10-rc3 to v2024.10
- Move U-Boot patch dir to default one (`$BOOTBRANCH/board_$BOARD`) which gets applied automatically by the patcher for the specific $BOARD
- Little fixes: Use `declare -g` and a code style similar to NanoPi R6 series
Removed gpio-keys node (NOTE: add to the M4 Berry DTS)
Add vcc1v8 and vcc3v3 regulators
Fixup MMC nodes
Add bluetooth node (NOTE: BT is still iffy in Armbian)
Signed-off-by: Patrick Yavitz <pyavitz@gmail.com>
Re-extract the kernel patches as a series.
Re-extract the u-boot patches as "git format-patch" command.
Unified patch extraction makes it easier to work with patches.
- in main `rockchip64` family, for current/edge (6.6 / 6.11)
- using mainline u-boot's generic rk3568 for current/edge
- vendor kernel is added via a copypasta hook to piggyback on `rk35xx`
- requires armbian/linux-rockchip PR https://github.com/armbian/linux-rockchip/pull/245
- vendor u-boot:
- is required to bringup npu for vendor kernel (otherwise panics)
- .dts done based on vendor kernel DT + looking at armsom-sige3
- defconfig ripped off from armsom-sige3
There are three revs: AM-GZ80x, AM-GZ80x-US and SC-GZ80x
Add a DSTI in case one should drop out of the sky and we
need a DTS for it. This also removes its dependency on
meson-axg-jethome-jethub-j1xx.dtsi.
Can now power down via power button on the back of the
unit and power back on via reset button on the side.
Signed-off-by: Patrick Yavitz <pyavitz@gmail.com>
