* Create rk3588-orangepi-5-ultra.dts
* Create orangepi5-ultra.csc
* fixups
* add notes
* fix u-boot compilation
* Update to v7 patch series
https://patchwork.kernel.org/project/linux-arm-kernel/cover/20250222193332.1761-1-honyuenkwun@gmail.com/
* Update rk3588-orangepi-5-ultra.dts
While I don't fully understand either the `kernel-dtb` command nor the dt syntax itself for some reason the `nophandles` version stripped more than actually phandles. Lets see what happens this way.
* Delete patch/kernel/integrate-6.15/0001-tools-Makefile-remove-pci-target.patch
* disable OPTEE
c81f89ca90
- as Armbian u-boot is possibly deployed to SPI (replacing Petitboot),
try to make as compatible as possible; eg enable squashfs support
- in this case, `setexpr` and `fileenv` are used by HAOS
- found `fileenv` here 049e1a1949
Signed-off-by: Ricardo Pardini <ricardo@pardini.net>
Follow change from radxa 738cda44532c324e07296c95751e3083fa95f282.
Change with command:
sed -i "/CONFIG_OPTEE/d" patch/u-boot/legacy/u-boot-radxa-rk35xx/defconfig/*
Contains rewritten dts, based on decompiled dtb from original Klipad50
(as similiar as possible to original).
Kernel defconfig taken from MKSPI (replaced "mkspi" with "mksklipad50")
* add nanopi-r3s.csc board config
* Nanopi R3S - add uboot patch
* Nanopi R3S - add dts
* fix bogus patch header
* Migrate to new patch series
Source & credits https://patchwork.ozlabs.org/project/uboot/list/?series=438193
I still need to figure out how to convert a patch series from patchwork in a way so the build framework doesn't complain about headers and magic and whatever. So a few hundreds of header lines have been replaced with something generic.
Applies and builds fine now against current stable v2024.10
* Create board-nanopi-r3s-fix-leds.patch
Thx https://github.com/armbian/build/pull/7556#issuecomment-2615110100
* Rename board-nanopi-r3s-fix-leds.patch to xx-board-nanopi-r3s-fix-leds.patch
* add new patch
- also LEDs, networking, more supported compression methods...
- copypasta reigns supreme. refactor is coming, just not today
- also hack the u-boot dtsi for consistent-with-Linux-mainline-DT mmc/sd numbering
- this was previously a separate patch in 2024.10
* Correcting the Perf unit's interrupt source number to 66 as stated in the Allwinner A10User manual to resolve conflict with Uart 2 which actually uses interrupt source number 3
* rename to all lower case and add in sun4i-emac dma support. Note that support only exist in the driver for the rx channel
* Ensure that sun4i patches actually implemented
Signed-off-by: Ryan L <ryestar101@gmail.com>
* Apply performance monitoring unit IRQ number patch to uboot
* Add patch for resolving the perf unit irq number to the edge kernel
Signed-off-by: Ryan L <ryestar101@gmail.com>
* Add sun4i emac ethernet DMA support to the edge kernel
Signed-off-by: Ryan L <ryestar101@gmail.com>
* Append missing .patch so that our patch is found and works properly
Signed-off-by: Ryan L <ryestar101@gmail.com>
* Apply EMAC DMA support and PMU fix to edge kernel
---------
Signed-off-by: Ryan L <ryestar101@gmail.com>
