* SakuraPi RK3308B: Move to official support
* Sakura Pi RK3308B: Use mainline dts instead
* Sakura Pi RK3308B: Fix brcm wlan broken due to sdio freq was set too high
* Sakura Pi RK3308B: Fix vop panel outpout and spidev
Enable mainline kernel (current/edge) for the NanoPi Zero2 (RK3528):
- Add current,edge to KERNEL_TARGET
- Override BOOT_FDT_FILE to rk3528-nanopi-zero2.dtb for mainline branches
(vendor kernel uses rk3528-nanopi-rev01.dtb)
- Set SERIALCON=ttyS0 and patch boot script for mainline, as RK3528 debug
UART is UART0 (ttyS0), not UART2 (ttyS2) like other RK35xx SoCs
Tested on hardware with kernel 6.18 (current branch).
- Freeze KERNELBRANCH at v6.12.28 for current branch
- Fix max_hdmi_phy_freq value from 1650000000 to 1650000 Hz
Signed-off-by: Igor Pecovnik <igor@armbian.com>
Was only used once (orangepi5pro.csc) and has been deprecated.
Remove the implementation, the board config, and the README entry.
Co-Authored-By: Claude Sonnet 4.6 <noreply@anthropic.com>
Add konsole to the kde-neon base package list for a complete terminal experience.
Also add bluedevil, kscreen, pipewire-audio, pipewire-pulse, and wireplumber,
and sort the entire package list alphabetically.
Driver for Ethernet/PCI as found with Xunlong/Ky on the
OrangePi RV2/R2S source tree. Added as kernel patch since
the current spacemit family has conflicting changes with
rtl8852bs when enabling EXTRAWIFI=yes
Note: on the Xunlong/Ky tree, there is also a realtek_pgtool/
subdir that compiles a pgdrv.ko. B/c this does not have a
license indication, is only needed e.g. for MAC address
programming of efuse / eeprom, and generally does not look
required this is ommited here. For details, you may refer
to https://github.com/redchenjs/rtnicpg
Signed-off-by: Sven-Ola Tuecke <sven-ola@gmx.de>
Disable U-Boot CONFIG_MMC_UHS_SUPPORT otherwise a fast SD card does not
report "1.8 Volt mode switch possible" on kernel init which in turn does
not enable SDR104 for my SDXC card.
Fast mode ok is visible in the kernel log after booting from SD card:
root@orangepirv2:~# dmesg |grep mmc
[ 2.198816] mmc0: SDHCI controller on d4280000.sdh [d4280000.sdh] using ADMA
[ 2.224576] mmc1: SDHCI controller on d4280800.sdh [d4280800.sdh] using ADMA
[ 2.272657] mmc0: set tx_delaycode: 159
[ 2.273950] mmc0: pass window [6 68)
[ 2.276301] mmc0: pass window [72 198)
[ 2.277591] mmc0: pass window [219 255)
[ 2.277599] mmc0: tuning done, use the firstly delay_code:134
[ 2.277611] mmc0: new ultra high speed SDR104 SDXC card at address b36b
With UHS already enabled in u-boot, no tuning and no SDR104 mode is switched on
in the Linux kernel. Seems to be a side effect of an un-complete mmc_deinit() in
u-boot/driver/mmc/mmc.c. With MMC_UHS_SUPPORT disabled, the SD card does report
SD_ROCR_S18A with then leads to enter spacemit_sdhci_execute_sw_tuning() and the
subsequent switch to SDK104 or probably other 1.8 Volt modes is fine. This is at
least true for my OrangePi RV2 board.
Signed-off-by: Sven-Ola Tuecke <sven-ola@gmx.de>
- u-boot v2026.04-rcX has bumped dt-rebasing to v6.18, thus it knows about
NPU nodes now and we can simply symlink to kernel DT, reducing duplication by a lot
- rockchip64-6.19: mainline kernel (edge/6.19):
- most stuff works, incl 4G modem, NPU, RS-485, RS-232, HDMI-RX
- except:
- type-c (fusb302, I've no schematics nor will to reverse)
- DisplayPort (I don't have test hardware)
- Analog Audio (ditto)
- keep vendor u-boot for vendor branch
- mainline u-boot v2026.01:
- same DT as edge kernel, save for NPU nodes
- boot order: NVMe -> SATA -> USB -> eMMC -> Ethernet/PXE
- stable MAC addresses for GMAC0/1 via DT aliases (confirm with logging patch)
This commit enables generation of `u-boot-rockchip-spi-sata.bin`.
Flashing this to SPI flash enables U-Boot to communicate with an
attached SATA m.2 SSD, thereby allowing booting directly from SPI flash
to SATA SSD.
CONFIG_ROCKCHIP_MINI_KERNEL implicitly sets
CONFIG_DTC_OMIT_DISABLED=y
CONFIG_DTC_OMIT_EMPTY=y
this causes bundled devicetree overlays which set nodes to "disabled" to become noop.
Disable these DTC_OMIT options to restore overlay disable functionality.
