A new kernel change (see https://lkml.org/lkml/2020/9/16/1323) introduces
significant instabilities in the RTL8211E Ethernet interface; this patch
reverts that change so that the RTL8211E works reliably again.
It seems that Charger LED support for AXP20X-like PMICs (AXP813, ...) from Megous is less complete then from Olimex. Reverting the one in the tree and ading the one from Olimex
* Add HDMI sound support for Allwinner A10, A20, A31
Closes https://github.com/armbian/build/issues/2084
* Enable HDMI audio in kernel config and update config with misc modules
* Bump sunxi to 5.7.y
* Further cleanup 32bit works, 64bit needs more patches adjustement
* Also arm64 boots, SPI flash areas were refactored, new location is a bit fuzzy, leaving behind
* More fixed and cleanings, both variants builds now, but without overlay support
* fix sunxi overlays in AR-329 branch
Signed-off-by: Igor Pecovnik <igor.pecovnik@gmail.com>
Co-authored-by: Martin Ayotte <martinayotte@yahoo.ca>
We don't need to enable UARTS and OTG by default on all Nanopi boards. This seems to cause instability on M1
Signed-off-by: Igor Pecovnik <igor.pecovnik@gmail.com>
There have been intermittent issues with SPDIF output on H3 & H2+ devices.
Digging into the H2+ & H3 datasheets I encountered an important clue on
table 8.7.2.2: s_clk needs to be 4x24.576 MHz or 4x22.5782 Mhz.
Probably due to how SPDIF is a huge oversample of the audio frequency.
Co-authored-by: George Lander <lander@jagmn.com>
deleted activation of i2s1 - 1c2240, because it isnt necessary for the corect operation of audio-analog and sound_hdmi
USB isnt affected.
i2s2 is right, because its needed for sound_hdmi 1c22800
* npi-a64-only-audio-usb.patch
This is a follow-up to the PR #1927 where the complete sun50i-a64.dtsi was changed.
This is a patch ONLY for the NanoPi A64 .dts to activate Audio & Upper USB-port
Has been build/compiled and works with focal 5.6.5
Address = Alias:
sound=sound
sound_hdmi = sound_hdmi
1c19000 = usb_otg
1c22400 = i2s1
1c22c00 = dai
1c22e00 = codec
1c22800 = i2s2
1f015c0 = codec_analog
* Create npi-a64-only-audio-usb.patch
Co-authored-by: Igor Pečovnik <igorpecovnik@users.noreply.github.com>
* Add 8189es out of the tree patch from repository.
* Added 8189FS version
* Support building on kernel 5.6. for 88x2bu
Tested for building on legacy, current and dev, removed old patches
* kernel: linux-sunxi-{dev,current}: Enable CONFIG_BT_HCIUART_BCM
This patch returns Broadcom's protocol for bluetooth HCI over serial port.
* BananaPiM2Zero: Patches for the devicetree
These patches add HDMI out (with audio) and add bluetooth / wifi
rfkill devices.
* [sunxi] allow pcm5102a codec module to be built
for sunxi-current and sunx-dev kernels.
Fixes#1798
* [sunxi] build pcm5102a and pcm51xx_(i2s|spi) modules by default
on sunxi-current and sunxi-dev kernels.
* Wireguard: bump tag to most recent since it breaks building on 5.4.y
* Move rockchip current to 5.4.y
* Move sunxi current to 5.4.y
* Move meson64 to 5.4.y
* Move odroidxu4 to 5.4.y and enable "current" targets
* Enable missing target
this update of the previous patch (#1663) additionally fixes the following overlays:
sun5i-a13: i2c1..2, nand, pwm, spi2, uart0..3
sun4i-a10: can, i2c1..2, pwm, spdif-out, spi0..2
corrections re #1663:
sun7i-a20: fixed typo in pwm overlay in #1663
arch64-makefile now back in line with original patch
some armbian dts overlays currently do not work since pinctrl names have not been
adapted to renaming in 5.0 and 5.2.
this patch modifies the following overlays:
sun50i-h5: cir, spdif-out
sun8i-h3: cir, spdif-out
sun7i-a20: i2c1..4, mmc2, pwm, spdif-out, spi0..2, spi-add-cs1, uart4..7
sun5i-a13: uart0
sun4i-a10: spdif-out
* Sunvell R69: cpu voltage regulator (re-)added - dram clock reduced.
CPU regulator (re-)added to u-boot and kernel dts - the box will not boot without it.
Dram clock reduced in defconfig to increase stability.
[AR-85]
AR-1 - Adding support category for distributions
AR-4 - Remove Allwinner legacy
AR-5 - Drop Udoo family and move Udoo board into newly created imx6 family
AR-9 - Rename sunxi-next to sunxi-legacy
AR-10 - Rename sunxi-dev to sunxi-current
AR-11 - Adding Radxa Rockpi S support
AR-13 - Rename rockchip64-default to rockchip64-legacy
AR-14 - Add rockchip64-current as mainline source
AR-15 - Drop Rockchip 4.19.y NEXT, current become 5.3.y
AR-16 - Rename RK3399 default to legacy
AR-17 - Rename Odroid XU4 next and default to legacy 4.14.y, add DEV 5.4.y
AR-18 - Add Odroid N2 current mainline
AR-19 - Move Odroid C1 to meson family
AR-20 - Rename mvebu64-default to mvebu64-legacy
AR-21 - Rename mvebu-default to mvebu-legacy
AR-22 - Rename mvebu-next to mvebu-current
AR-23 - Drop meson64 default and next, current becomes former DEV 5.3.y
AR-24 - Drop cubox family and move Cubox/Hummingboard boards under imx6
AR-26 - Adjust motd
AR-27 - Enabling distribution release status
AR-28 - Added new GCC compilers
AR-29 - Implementing Ubuntu Eoan
AR-30 - Add desktop packages per board or family
AR-31 - Remove (Ubuntu/Debian) distribution name from image filename
AR-32 - Move arch configs from configuration.sh to separate arm64 and armhf config files
AR-33 - Revision numbers for beta builds changed to day_in_the_year
AR-34 - Patches support linked patches
AR-35 - Break meson64 family into gxbb and gxl
AR-36 - Add Nanopineo2 Black
AR-38 - Upgrade option from old branches to new one via armbian-config
AR-41 - Show full timezone info
AR-43 - Merge Odroid N2 to meson64
AR-44 - Enable FORCE_BOOTSCRIPT_UPDATE for all builds
* Fix wifi
patch "board-h2plus-nanopi-duo-add-device.patch": increase post-power-on-delay-ms from 50ms to 200ms in wifi_pwrseq node in nanopi-duo dts [dev-branch].
Change in line with other XRADIO device trees (orange pi zero, sunvell).
See also Pull Request #1605.
* Fix xradio patch (dev-branch)
fix KConfig to 5.x - WLAN_VENDOR-flag set to "y" in line with other drivers - otherwise module not loaded.
* correct device name
change nodes "model" and "compatible" to correct device name (from "NanoPi Duo AIR" to "NanoPi Duo") [dev-branch]
Not functionally necessary, but more correct.
