1a12994e79
* [Early WIP] Update sunxi-next to kernel 4.17 * Switch Allwinner 32 and 64bit to U-boot 2018.05 * Adjust patched for 4.17.y / sunxi-next - adjust both configurations - removing FAT support from u-boot (breaks if you try to save) Tested those boards: Cubietruck: wlan fails http://ix.io/1fYS USB OK, HDMI yes Bananapi R40: http://ix.io/1fZm USB OK, HDMI yes Lime A64: USB no, HDMI no, wireless buggy, eMMC yes Orangepi prime H5: OK http://ix.io/1fZJ DVFS no Orangepi2e: DVFS OK, HDMI OK, net OK, wifi OK, eMMC ok, http://ix.io/1fZT * Kernel config update, enabling HDMI on CT+ * Trying to fix A64 HDMI but failed. Fixed M64 ethernet instead * Update orangepioneplus.wip * Update orangepioneplus.wip * Fix H6 build process * Add regulator bits for Orangepizero+, thanks to @5kft * add H5 support for optional 1.3v regulator and 1.3GHz operation This patch adds two optional overlays that can be used to: 1) enable the 1.1v/1.3v regulator on boards that provide the necessary compatible H/W support 2) modify the default CPU clock operating table to add new 1.2GHz and 1.3GHz clocks Note that the generated regulator overlay will only support boards whose 1.1v/1.3v regulator is controlled by GPIO PL6. * updates for the NanoPi NEO Plus2 This change introduces a patch that provides two changes for the NanoPi NEO Plus2: * Configure the "cpu0" to use the "vdd_cpux" regulator; this enables the ability to use higher CPU clocks * Correct the configurations of the on-board power and status LEDs * Adjust nightly building and few boards config cleanup
61 lines
1.6 KiB
Diff
61 lines
1.6 KiB
Diff
diff --git a/arch/arm64/boot/dts/allwinner/sun50i-h5-orangepi-zero-plus2.dts b/arch/arm64/boot/dts/allwinner/sun50i-h5-orangepi-zero-plus2.dts
|
|
index b6b7a561..6f959afb 100644
|
|
--- a/arch/arm64/boot/dts/allwinner/sun50i-h5-orangepi-zero-plus2.dts
|
|
+++ b/arch/arm64/boot/dts/allwinner/sun50i-h5-orangepi-zero-plus2.dts
|
|
@@ -64,6 +64,12 @@
|
|
regulator-min-microvolt = <3300000>;
|
|
regulator-max-microvolt = <3300000>;
|
|
};
|
|
+
|
|
+ wifi_pwrseq: wifi_pwrseq {
|
|
+ compatible = "mmc-pwrseq-simple";
|
|
+ reset-gpios = <&pio 0 9 GPIO_ACTIVE_LOW>; /* PA9 */
|
|
+ post-power-on-delay-ms = <50>;
|
|
+ };
|
|
};
|
|
|
|
&mmc0 {
|
|
@@ -75,6 +81,27 @@
|
|
status = "okay";
|
|
};
|
|
|
|
+&mmc1 {
|
|
+ pinctrl-names = "default";
|
|
+ pinctrl-0 = <&mmc1_pins_a>;
|
|
+ vmmc-supply = <®_vcc3v3>;
|
|
+ vqmmc-supply = <®_vcc3v3>;
|
|
+ mmc-pwrseq = <&wifi_pwrseq>;
|
|
+ bus-width = <4>;
|
|
+ non-removable;
|
|
+ status = "okay";
|
|
+
|
|
+ brcmf: brcmf@1 {
|
|
+ reg = <1>;
|
|
+ compatible = "brcm,bcm4329-fmac";
|
|
+ interrupt-parent = <&r_pio>;
|
|
+ interrupts = <0 7 IRQ_TYPE_LEVEL_LOW>; /* PL7 / EINT7 */
|
|
+ interrupt-names = "host-wake";
|
|
+ pinctrl-names = "default";
|
|
+ pinctrl-0 = <&wifi_wake>;
|
|
+ };
|
|
+};
|
|
+
|
|
&mmc2 {
|
|
pinctrl-names = "default";
|
|
pinctrl-0 = <&mmc2_8bit_pins>;
|
|
@@ -85,6 +112,14 @@
|
|
status = "okay";
|
|
};
|
|
|
|
+&r_pio {
|
|
+ wifi_wake: wifi_wake@0 {
|
|
+ pins = "PL7";
|
|
+ function = "irq";
|
|
+ bias-pull-up;
|
|
+ };
|
|
+};
|
|
+
|
|
&uart0 {
|
|
pinctrl-names = "default";
|
|
pinctrl-0 = <&uart0_pins_a>;
|