1a12994e79
* [Early WIP] Update sunxi-next to kernel 4.17 * Switch Allwinner 32 and 64bit to U-boot 2018.05 * Adjust patched for 4.17.y / sunxi-next - adjust both configurations - removing FAT support from u-boot (breaks if you try to save) Tested those boards: Cubietruck: wlan fails http://ix.io/1fYS USB OK, HDMI yes Bananapi R40: http://ix.io/1fZm USB OK, HDMI yes Lime A64: USB no, HDMI no, wireless buggy, eMMC yes Orangepi prime H5: OK http://ix.io/1fZJ DVFS no Orangepi2e: DVFS OK, HDMI OK, net OK, wifi OK, eMMC ok, http://ix.io/1fZT * Kernel config update, enabling HDMI on CT+ * Trying to fix A64 HDMI but failed. Fixed M64 ethernet instead * Update orangepioneplus.wip * Update orangepioneplus.wip * Fix H6 build process * Add regulator bits for Orangepizero+, thanks to @5kft * add H5 support for optional 1.3v regulator and 1.3GHz operation This patch adds two optional overlays that can be used to: 1) enable the 1.1v/1.3v regulator on boards that provide the necessary compatible H/W support 2) modify the default CPU clock operating table to add new 1.2GHz and 1.3GHz clocks Note that the generated regulator overlay will only support boards whose 1.1v/1.3v regulator is controlled by GPIO PL6. * updates for the NanoPi NEO Plus2 This change introduces a patch that provides two changes for the NanoPi NEO Plus2: * Configure the "cpu0" to use the "vdd_cpux" regulator; this enables the ability to use higher CPU clocks * Correct the configurations of the on-board power and status LEDs * Adjust nightly building and few boards config cleanup
25 lines
708 B
Diff
25 lines
708 B
Diff
diff --git a/arch/arm/boot/dts/sun8i-h3-orangepi-pc-plus.dts b/arch/arm/boot/dts/sun8i-h3-orangepi-pc-plus.dts
|
|
index 8b93f5c..9011356 100644
|
|
--- a/arch/arm/boot/dts/sun8i-h3-orangepi-pc-plus.dts
|
|
+++ b/arch/arm/boot/dts/sun8i-h3-orangepi-pc-plus.dts
|
|
@@ -51,6 +51,11 @@
|
|
/* ethernet0 is the H3 emac, defined in sun8i-h3.dtsi */
|
|
ethernet1 = &rtl8189ftv;
|
|
};
|
|
+
|
|
+ wifi_pwrseq: wifi_pwrseq {
|
|
+ compatible = "mmc-pwrseq-simple";
|
|
+ reset-gpios = <&r_pio 0 7 GPIO_ACTIVE_LOW>; /* PL7 WIFI_EN */
|
|
+ };
|
|
};
|
|
|
|
&mmc1 {
|
|
@@ -57,6 +57,7 @@
|
|
pinctrl-names = "default";
|
|
pinctrl-0 = <&mmc1_pins_a>;
|
|
vmmc-supply = <®_vcc3v3>;
|
|
+ mmc-pwrseq = <&wifi_pwrseq>;
|
|
bus-width = <4>;
|
|
non-removable;
|
|
status = "okay";
|