1a12994e79
* [Early WIP] Update sunxi-next to kernel 4.17 * Switch Allwinner 32 and 64bit to U-boot 2018.05 * Adjust patched for 4.17.y / sunxi-next - adjust both configurations - removing FAT support from u-boot (breaks if you try to save) Tested those boards: Cubietruck: wlan fails http://ix.io/1fYS USB OK, HDMI yes Bananapi R40: http://ix.io/1fZm USB OK, HDMI yes Lime A64: USB no, HDMI no, wireless buggy, eMMC yes Orangepi prime H5: OK http://ix.io/1fZJ DVFS no Orangepi2e: DVFS OK, HDMI OK, net OK, wifi OK, eMMC ok, http://ix.io/1fZT * Kernel config update, enabling HDMI on CT+ * Trying to fix A64 HDMI but failed. Fixed M64 ethernet instead * Update orangepioneplus.wip * Update orangepioneplus.wip * Fix H6 build process * Add regulator bits for Orangepizero+, thanks to @5kft * add H5 support for optional 1.3v regulator and 1.3GHz operation This patch adds two optional overlays that can be used to: 1) enable the 1.1v/1.3v regulator on boards that provide the necessary compatible H/W support 2) modify the default CPU clock operating table to add new 1.2GHz and 1.3GHz clocks Note that the generated regulator overlay will only support boards whose 1.1v/1.3v regulator is controlled by GPIO PL6. * updates for the NanoPi NEO Plus2 This change introduces a patch that provides two changes for the NanoPi NEO Plus2: * Configure the "cpu0" to use the "vdd_cpux" regulator; this enables the ability to use higher CPU clocks * Correct the configurations of the on-board power and status LEDs * Adjust nightly building and few boards config cleanup
36 lines
877 B
Diff
36 lines
877 B
Diff
diff --git a/arch/arm64/boot/dts/allwinner/sun50i-a64-olinuxino.dts b/arch/arm64/boot/dts/allwinner/sun50i-a64-olinuxino.dts
|
|
index 3b3081b..24cde3d 100644
|
|
--- a/arch/arm64/boot/dts/allwinner/sun50i-a64-olinuxino.dts
|
|
+++ b/arch/arm64/boot/dts/allwinner/sun50i-a64-olinuxino.dts
|
|
@@ -58,6 +58,13 @@
|
|
stdout-path = "serial0:115200n8";
|
|
};
|
|
|
|
+ reg_vcc3v3: vcc3v3 {
|
|
+ compatible = "regulator-fixed";
|
|
+ regulator-name = "vcc3v3";
|
|
+ regulator-min-microvolt = <3300000>;
|
|
+ regulator-max-microvolt = <3300000>;
|
|
+ };
|
|
+
|
|
wifi_pwrseq: wifi_pwrseq {
|
|
compatible = "mmc-pwrseq-simple";
|
|
reset-gpios = <&r_pio 0 2 GPIO_ACTIVE_LOW>; /* PL2 */
|
|
@@ -92,6 +99,16 @@
|
|
};
|
|
};
|
|
|
|
+&mmc2 {
|
|
+ pinctrl-names = "default";
|
|
+ pinctrl-0 = <&mmc2_pins>;
|
|
+ vmmc-supply = <®_vcc3v3>;
|
|
+ bus-width = <8>;
|
|
+ non-removable;
|
|
+ cap-mmc-hw-reset;
|
|
+ status = "okay";
|
|
+};
|
|
+
|
|
&r_rsb {
|
|
status = "okay";
|
|
|