* sunxi: kernel: current/dev: enable sun6i-csi and disable LL debug on UART0
The former is useful on some boards, e.g. PineCube.
The latter blocks boards that do not utilize UART0 from booting.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
* sunxi: add new family sun8i-v3s
This family is intended for boards with V3/V3s/S3/S3L chips and low
DRAM capacity.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
* sunxi: add PineCube board
This board features Sochip S3 SoC (Allwinner V3 die + co-packaged 128MiB
DRAM), and an OmniVision OV5640 camera is shipped with the board.
Add support for it. It could be used as an IP camera then.
Kernel support is only added to current/dev branch, with dev just using
mainline-merged DT and current using backported DT from 5.10-rc.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
* sunxi: kernel: current/dev: add V3s OHCI/EHCI nodes
These are needed for USB host on V3s boards to work.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
* update fancontrol configuration
* Enable network activity led, default to eth0
* Do not disable auto poweron on power loss event
* Added UPS timer
Provide timer to poweroff system after 600 s (10 minutes) of power loss
event. If power restored within that time window, cancel the timer.
* Use different service for legacy
LK 4.4 does not have ledtrig-netdev, so it will cause the service to
fail.
* Use 10m instead 600 seconds in UPS timer
Systemd time can use m suffix for minutes. Use this to make it easier to
read.
- move Odroid C4 from legacy u-boot toward mainline
- get rid of dirty legacy u-boot code
- get rid of FAT boot partition
- briefly tested
- both kernels can operate with one standard boot script
- add upstream patch and adjust config
- fix console
- don't clock C4 too high by default
Removed default-sample-phase property for base rk322x-box device tree
Enabled spdif out for rk322x-current and -dev flavours
Removed reserved node in device tree, u-boot v2020.10 and OPTEE autoconfigure reserved zones automatically
* Switched RockPro64 to mainline u-boot
* Enabled rockusb and ums for RockPro64 in mainline u-boot
* Switched RockPro64 u-boot to TPL/SPL/BLOB scenario
* Enabled advanced recovery button support for RockPro64
* Disabled SDR104 mode for RockPro64 in legacy
* Switched Pinebook Pro to mainline u-boot
* Some Pinebook Pro mainline u-boot tweaks
(based on https://github.com/pcm720/u-boot-build-scripts)
* Removed Pinebook Pro legacy u-boot support
Pinebook-Pro Support:
suspend to idle via key and lid close
brightness keys
volume control keys
wifi, bluetooth frimware
touchpad tweaks
keyboard config
armbian-hardware-optimization
bootsplash
Co-authored-by: Britt Dodd <britt@reactornet.net>
- Chanaged default x.org configuration to disable glamor
- Reintroduce patch to use DRM cursor plane as overlay in rk322x-current and -dev
- Updated wifi patches for kernel 5.8.10
- Bumped rk322x to u-boot v2020.07, removed reserved zones from device trees
- Updated OPTEE to v3.10, using ddrbin v1.10
- Bumped rk322x-current to kernel 5.8.y
- Imported new patches from knaerzche's LibreELEC fork for rk322x-dev (kernel 5.8.y)
- Adjusted existing patches to match changes, updated rk322x-dev kernel config file
- Add default modprobe conf file for esp8089 to force the crystal frequency to 40Mhz for rk322x targets
- Removed ssv6051 firmware packages to move to armbian-firmware repository
- Switching ssv6051-wifi.cfg to /lib/firmware for rk322x-legacy
- Removed P2P interface for esp8089 driver for rk322x-legacy
- Optimized ssv6051 performance: kernel module gains -Os flag, disabled p2p interface, enabled HW crypto for CCMP cipher
- Enabled remote control interface, IR GPIO kernel module and HDMI CEC modules
* Helios64: rework vdd_log and vdd_center
* helios64: Use rockchip binaries for legacy and current branch
Fully open source bootloader only on dev branch
Signed-off-by: Aditya Prayoga <aditya@kobol.io>
* rework vdd_log and vdd_center patches
* Supress systemd service warning
* helios64: u-boot: staggered HDD power up
Set the delay to 10s in between turning on the next HDD power rails.
Remove the delay property from kernel device tree, let it only apply to
u-boot
Signed-off-by: Aditya Prayoga <aditya@kobol.io>
* helios64: fault LED as kernel panic indicator
also sync, u-boot dts
* helios64: fix hwmon udev rules
Legacy kernel (LK 4.4) has different class/naming on SoC Temp sensor.
Also fix typo on current/dev udev rules.
* bsp: helios64: Add fancontrol
- Fancontrol configuration
- Udev rules for fan and temp sensor
Signed-off-by: Aditya Prayoga <aditya@kobol.io>
* bsp: helios64: Enable heartbeat on system status led
The reason systemd service used instead of device tree modification, is
to give visual notification that the system is ready.
Signed-off-by: Aditya Prayoga <aditya@kobol.io>
* armbian-hardware-optimization: SATA & 2.5GbE IRQ pinning on Helios64
- 2.5GbE USB LAN which is attached to XHCI, assigned to CPU4
- SATA controller assigned to CPU4 and CPU5
Signed-off-by: Aditya Prayoga <aditya@kobol.io>
* Moving Rockchip 32bit to 5.8.y
xt-q8l-v10 seems to be broken. I did a quick scan but couldn't resolve it. @paolosabatino
* Add wifi patches for 5.8.y
* [rockchip] Fixed xt-q8l-v10 DTS, reworked ath9k driver patch for 5.8.y (#2184)
* Fixed xt-q8l-v10 device tree to work on kernel 5.8.y on rockchip-current and -dev
* Reworked ath9k driver patch to compile on kernel 5.8.y for rockchip-current and -dev
* Add also wifi patches to DEV kernel
Co-authored-by: Paolo <paolo.sabatino@gmail.com>
* Switched rockchip64 curent to kernel 5.8.y
* Enforce CRLF in one of the wifi patches for rockchip64-current
* Removed uneeded wifi patches for rtl8189fs from rockchip64-current
