* `odroidm1`.wip: hk's `legacy`= 4.19 and `edge`= mainline+tobetter's 5.19 rebased; *requires* `skip_spiboot=true`
- @TODO: family/etc naming is terrible with vendor kernels. Sorry. Fight over it and let me know?
- @TODO: config is very probably incomplete.
- new `boot-rockchip64-vendor.cmd`:
- does not use fixed load_addr, instead use ramdisk_addr_r for everything
- load kernel and initrd as late as possible
- look for overlays twice:
- once: with prefix and folder
- twice: without prefix, nor folder; helps with vendor provided overlays like hk's and tobetter's
- wip: edge: tobetter's patchset rebased against 5.19.3
- wip: edge: bump to tobetter's 5.19
- legacy: .config `CONFIG_ARM64_VA_BITS_48=y`
- wip m1: update legacy config from odroid
- odroidm1: container/bpf stuff in legacy config
* Update configs and enable beta build target
* Adjust current kernel
* Update targets
* Remove everything but EDGE kernel
* Cleanup
* Fix
Co-authored-by: Ricardo Pardini <ricardo@pardini.net>
* Go back to latest stable u-boot with VIM3L
https://github.com/armbian/build/pull/4251
* Revert "Go back to latest stable u-boot with VIM3L"
This reverts commit 0b240563ef.
* meson64: allow board-specific `BOOTBRANCH`; `khadas-vim3l`: `BOOTBRANCH_BOARD=tag:v2022.04`
Co-authored-by: Ricardo Pardini <ricardo@pardini.net>
* sunxi-6.0: initial state: add megous patches to series
* sunxi-6.0: Switch to v6.0.1
* wifi: Limit the version 6.0 for Realtek 88x2cs chipsets
* Adjust kernel configs
* Remove not needed patches
* Adjust broken patches
Co-authored-by: Igor <igor@armbian.com>
* Remove deprecated Odroid XU4 legacy 4.14.y branch
* Clean deprecated kernels from meson64 family
- legacy kernel 4.9 was removed
- current 5.10 was replaced with 5.19
- edge remains on 5.19 until someone bumps it to 6
- patches between 5.11 and 5.18 were removed, 5.10 will be kept for awhile
* Update configs
* RockPI-S board has no video I/O
* udev rule to fix MAC address of iface based on UUID
Deals with WiFi chip lacking any EEPROM to store its unique Ethernet MAC address
Generic mechanism -- could be utilized for other boards having similar issues
* Handy Device Tree overlays for the RockPI S
Use armbian-add-overlay to install these
Reduce CPU voltage for the RK3308 B-S
Option to overclock RK3308 B-S to 1.3Ghz
Increase SDIO clock rate from 1Mhz to 10Mhz
This increases WiFi throughput from 300K bytes/s to 2.4M bytes/s
* corrected comment
* No longer repeat standard opp's in this dts
Require that the standard bs dts already be installed
* User README for adding RockPI-S board variant specific dts overlays
* "enabled" --> "okay"
* added mention of sdnand.dts, fixed typo
* added p2p0 to interfaces whose MAC address should be "fixed"
* RK3308 CPU serial number in nvmem replaces UUID for derivation of fixed MAC addr
Restored use of install utility
* Use RK3308 specific CPU serial number
rather than rootfs UUID
* remove generic fixMACaddress
* Install fixMACaddr file-by-file via install utility
* Drive SDIO bus signals faster
setting RK3308_SOC_CON0_VCCIO3 reduces signal rise/fall times to WiFi SDIO chip
from 30ns to 5ns.
This odd fix forward ported from legacy kernel.
Allows Rock Pi-S WiFi to operate at full speed.
* Set RK3308 I/O voltage domains before SDIO initializes
This patch moves responibility form the io-domain to the pinctrl driver because
the io-domain driver is probed after the SDIO devices are discovered.
This was causing multiple SDIO I/O failures during boot.
A new pinctrl property is added:
io-1v8-domains
is a u32 interpreted as a bit mask where each set bit corresponds to
a 1.8V I/O domain (as opposed to the default of 3.3V for I/O)
The mask is writted to the RK3308_SOC_CON0 GRF register
(once) when the pinctrl driver starts
The default mask is 0x10 where only I/O domain 4 runs at 1.8V
This is necessary for the RockPI-S to run the SDIO clock at high (50Mhz) speed
* align whitespace
* factored rk3308bs overlays out up sdio speedup patch
* factored dts for RK3308 iodomains and pinctrl patches out of speedup patch
* remains of sdio speedup patch merely add iodomains support for rk3308
* factored rockpis dts modification out from rk3308 io voltage domains
replaced rk3308 support from iodomains with
new io-voltage-domains property added to pinctrl
io-voltage-domains specific to rk3308 for now, others SOCs may be added later.
* add sequence numbering to names of rk3308 patches
* corrected tab alignment
* Bump sunxi kernels
* sunxi-5.19: Remove pre-applied patch, adapt for series
* sunxi-5.15: Adapt patches to the series, remove previously applied
* Bump it again
Co-authored-by: The-going <48602507+The-going@users.noreply.github.com>
* Add wallpaper to grup, set fixed screen size, enable hidpi mode on lightdm
* Enable graphics terminal on UEFI x86, ARM64 can't test
* Missing folder
* Enable `Plymouth`
* Add proper HiDpi support and enable intel graphics auto probing
Tested on Intel and Nvidia, both works OOB. Plymouth works as expected, no text logs on screen, if OEM vendor logo is present, it picks it up auto, otherwise shows armbian (chip) logo
Co-authored-by: hzy <hzyitc@outlook.com>
* Add plymouth-theme-armbian package
* Adjust all bootscripts to adapt plymouth
* Auto show logo accroding to BOOT_LOGO
* Enable plymouth detail mode when bootlogo=false
* Add a new board config var - HAS_VIDEO_OUTPUT
This var is used to indicate whether device has a HW video output.
If it's set to "no", we will disable kernel bootsplash, plymouth and BUILD_DESKTOP
* Rename package to be aligned with others
* Disable kernel bootloader, but keep the code for it
* Rather keep bootlogo in the kernel for a while, otherwise kernel upgrade will turn bootup into the darkness
Co-authored-by: Igor Pečovnik <igorpecovnik@users.noreply.github.com>
Co-authored-by: Igor <igor@armbian.com>
* meson: bump version
bump edge to thirdparty linux-5.18-rc7
bump current to linux-5.15
change legacy back to LTS linux-5.10
* Upgrade kernel config
* meson: edge and current: Enable NTFS3 driver
