- sunxi64_common.inc, sunxi_common.inc:
- change current setting of UBOOT_TARGET_MAP
to allow a probable overriding definition
in a board config file
fixes#4478
* Move all legacy u-boot patches under one general legacy folder
* Move 32b Rockchip under 2022.04 and legacy for Miqi
Tested
* Move Rock 3A patch dir under legacy
* Move / merge meson64 patch folder into v2022.07
Merge 2022.04 (mainly Rockchip 32) into 2022.07, tested
* Remove not needed patch
* Add last kernel version to config
* sunxi-6.0: initial state: add megous patches to series
* sunxi-6.0: Switch to v6.0.1
* wifi: Limit the version 6.0 for Realtek 88x2cs chipsets
* Adjust kernel configs
* Remove not needed patches
* Adjust broken patches
Co-authored-by: Igor <igor@armbian.com>
* Bump sunxi kernels
* sunxi-5.19: Remove pre-applied patch, adapt for series
* sunxi-5.15: Adapt patches to the series, remove previously applied
* Bump it again
Co-authored-by: The-going <48602507+The-going@users.noreply.github.com>
* sunxi-5.19: Initial state for megous patches
* Add the ability to do 5.19
* Move to 5.19
- tested both
- removed broken Opi Zero xradio driver https://armbian.atlassian.net/browse/AR-1280
* sunxi-5.19: fix tag for switch
* sunxi-5.19: Initial state for armbian patches
* sunxi-5.19: Add armbian patches to series.conf file
* sanxi-5.19: Add other 2 patches
* sunxi-5.19: Limit to use the 'wireless/xradio' module
Limit the kernel version to less than 5.19 to use
the 'wireless/xradio' module
Co-authored-by: Igor Pecovnik <igor.pecovnik@gmail.com>
* sunxi-5.18: rebase megous patces to v5.18.3
* sunxi-5.18: Add upstream patches - tag: orange-pi-5.18-20220609-1318
* Check applicability to version 5.18.3
* sunxi-5.18: switch to version 5.18.3
* Update kernel configs
* Switch sunxi edge to 5.18.y
* Move sunxi to 5.18.y and re-enable AUFS
* Change version - temporally to make a build from here
* Update config
* 88xx was fixed in the mean time.
* Put version back
* Fix sunxi legacy, disable aufs on 5.10.y since its broken
* Upstream changed in the mean time
* Add a patch to enable 8821cu compilation at 5.18
https://github.com/armbian/build/pull/3814
* Re-enable CONFIG_RTL8822BU in edge
* Update CONFIG_RTL8XXXU
* Bump imx6
* Bump uefi kernels to 5.18.y
* Bump mvebu64 and switch odroid xu4 to 5.18
* sunxi-5.17: update and switch to version 5.17.11
* remove the patch that appeared in the upstream kernel
upstream commit c06a99a6605f524ff5ef096646e9501fc905366e
* Add reg_ahci_5v status okay for bananapro board
* Bananapro: add AXP209 regulators
* Fix series.conf, Disable the patch that is not being applied.
* Fix linux-sunxi64-edge.config for v5.17.3
* Fix linux-sunxi-edge.config to v5.17.3
* Switch EDGE to core 5.17 for sunxi
* Remove the old rtl8723cs driver which is incompatible with the new kernel and cannot be used.
* Use AUFS if the kernel version is less than 5.16
* Print the last 20 lines of the log if the kernel compilation failed.
* Set KERNEL_VERSION_LEVEL to 5.17
Co-authored-by: Igor Pecovnik <igor.pecovnik@gmail.com>
* The initial state of a series of patches for sunxi-5.17
tag orange-pi-5.17-20220323-1423
* DEBUG for sunxi-5.17
* Add Armbian patches to 5.17
* Fix duplicate nodes for sun50i-h5-orangepi-pc2
* Fix reg_ahci_5v to status okay for bananapro board
* Remove an unused patch for an unsupported sun50i-h6-tanix-tx6 board
