- Add dwc2_force_mode(hsotg, true) call in USB_DR_MODE_HOST case
- Ensures proper host mode initialization for Rockchip platforms
- Applies to both 6.18 and 6.19 kernel patches
* SakuraPi RK3308B: Move to official support
* Sakura Pi RK3308B: Use mainline dts instead
* Sakura Pi RK3308B: Fix brcm wlan broken due to sdio freq was set too high
* Sakura Pi RK3308B: Fix vop panel outpout and spidev
* Use "armbian,spi-dev" compatible string instead of "rockchip,spidev"
as it is already registered in the spidev driver's OF match-table,
ensuring the driver binds correctly at runtime.
Enable the PCIe Gen2x1 controller and combo PHY on the NanoPi Zero2
to support the M.2 Key-E 2230 slot used for WiFi/BT cards (e.g. Intel
AX210).
The reset GPIO (gpio1 RK_PA2) and pinctrl (pciem1_pins) match the
vendor kernel device tree.
Note: Intel AX210 requires iwlwifi firmware >= v89
(iwlwifi-ty-a0-gf-a0-89.ucode) which may not be included in minimal
images. Install linux-firmware or armbian-firmware-full if needed.
Firmware available at:
https://git.kernel.org/pub/scm/linux/kernel/git/firmware/linux-firmware.git/tree/
Tested on hardware with Intel AX210 on kernel 6.18 (current branch).
- Freeze KERNELBRANCH at v6.12.28 for current branch
- Fix max_hdmi_phy_freq value from 1650000000 to 1650000 Hz
Signed-off-by: Igor Pecovnik <igor@armbian.com>
* uefi-arm64-6.18: fix stmmac Phytium driver compilation
Remove obsolete 'has_gmac' member assignment from struct plat_stmmacenet_data.
The field was removed in newer kernels as MAC version detection is now
handled automatically from hardware registers.
Fixes compilation error:
error: 'struct plat_stmmacenet_data' has no member named 'has_gmac'
* meson64-6.19: drop upstreamed odroid regulator boot-on patch
The Odroid HC4 regulator-boot-on fix has been upstreamed in kernel 6.19.
Original patch:
Fixes: 164147f094ec ("arm64: dts: meson-sm1-odroid-hc4: add regulators")
Fixes: 45d736ab17b4 ("arm64: dts: meson-sm1-odroid: add 5v regulator gpio")
Fixes: 1f80a5cf74a6 ("arm64: dts: meson-sm1-odroid: add missing enable gpio")
Fixes: 88d537bc92ca ("arm64: dts: meson: convert meson-sm1-odroid-c4 to dtsi")
* meson64-6.18: update meson-axg mmc phase configuration
Add amlogic,mmc-phase properties to sd_emmc_b and sd_emmc_c nodes
for proper MMC timing configuration on Amlogic AXG SoCs.
* Disable Pythium onboard nic driver
- that was for otg/ums bringup
- now `-u-boot.dts` does it instead
- add missing usbdp_phy0 with lane mux split with DP (type-c/DP)
- drop DP mux from usbdp_phy1 (which should just be type-a and no DP)
- for the Mekotronics R58X Pro LCD
- The Vinka VK2C21 (and pin-compatible VK2C21A/VK2C21B) is a memory-mapping
segment LCD controller that communicates over I2C. It can drive up to
128 segments (e.g. 32 SEG × 4 COM in 1/3 bias mode).
- Some SBCs wire this chip to GPIO pins without I2C pull-up
resistors, making the standard i2c-gpio (open-drain) driver unusable.
This driver therefore bit-bangs I2C in push-pull mode directly via GPIO,
requiring no external pull-ups.
- extra glyphs and fix for top-bar
Signed-off-by: Ricardo Pardini <ricardo@pardini.net>
Force GFP_DMA32 allocation for Rockchip IOMMU v2 page tables to fix
NPU operation on systems with >4GB RAM. Without this patch, IOMMU
allocates page tables above 4GB which the NPU cannot access, causing
DMA mapping failures.
Tested on ODROID-M1 with 8GB RAM, kernel 6.18.9-current-rockchip64.
