* `odroidm1`.wip: hk's `legacy`= 4.19 and `edge`= mainline+tobetter's 5.19 rebased; *requires* `skip_spiboot=true`
- @TODO: family/etc naming is terrible with vendor kernels. Sorry. Fight over it and let me know?
- @TODO: config is very probably incomplete.
- new `boot-rockchip64-vendor.cmd`:
- does not use fixed load_addr, instead use ramdisk_addr_r for everything
- load kernel and initrd as late as possible
- look for overlays twice:
- once: with prefix and folder
- twice: without prefix, nor folder; helps with vendor provided overlays like hk's and tobetter's
- wip: edge: tobetter's patchset rebased against 5.19.3
- wip: edge: bump to tobetter's 5.19
- legacy: .config `CONFIG_ARM64_VA_BITS_48=y`
- wip m1: update legacy config from odroid
- odroidm1: container/bpf stuff in legacy config
* Update configs and enable beta build target
* Adjust current kernel
* Update targets
* Remove everything but EDGE kernel
* Cleanup
* Fix
Co-authored-by: Ricardo Pardini <ricardo@pardini.net>
* Go back to latest stable u-boot with VIM3L
https://github.com/armbian/build/pull/4251
* Revert "Go back to latest stable u-boot with VIM3L"
This reverts commit 0b240563ef.
* meson64: allow board-specific `BOOTBRANCH`; `khadas-vim3l`: `BOOTBRANCH_BOARD=tag:v2022.04`
Co-authored-by: Ricardo Pardini <ricardo@pardini.net>
* sunxi-6.0: initial state: add megous patches to series
* sunxi-6.0: Switch to v6.0.1
* wifi: Limit the version 6.0 for Realtek 88x2cs chipsets
* Adjust kernel configs
* Remove not needed patches
* Adjust broken patches
Co-authored-by: Igor <igor@armbian.com>
* Remove deprecated Odroid XU4 legacy 4.14.y branch
* Clean deprecated kernels from meson64 family
- legacy kernel 4.9 was removed
- current 5.10 was replaced with 5.19
- edge remains on 5.19 until someone bumps it to 6
- patches between 5.11 and 5.18 were removed, 5.10 will be kept for awhile
* Update configs
* RockPI-S board has no video I/O
* udev rule to fix MAC address of iface based on UUID
Deals with WiFi chip lacking any EEPROM to store its unique Ethernet MAC address
Generic mechanism -- could be utilized for other boards having similar issues
* Handy Device Tree overlays for the RockPI S
Use armbian-add-overlay to install these
Reduce CPU voltage for the RK3308 B-S
Option to overclock RK3308 B-S to 1.3Ghz
Increase SDIO clock rate from 1Mhz to 10Mhz
This increases WiFi throughput from 300K bytes/s to 2.4M bytes/s
* corrected comment
* No longer repeat standard opp's in this dts
Require that the standard bs dts already be installed
* User README for adding RockPI-S board variant specific dts overlays
* "enabled" --> "okay"
* added mention of sdnand.dts, fixed typo
* added p2p0 to interfaces whose MAC address should be "fixed"
* RK3308 CPU serial number in nvmem replaces UUID for derivation of fixed MAC addr
Restored use of install utility
* Use RK3308 specific CPU serial number
rather than rootfs UUID
* remove generic fixMACaddress
* Install fixMACaddr file-by-file via install utility
* Drive SDIO bus signals faster
setting RK3308_SOC_CON0_VCCIO3 reduces signal rise/fall times to WiFi SDIO chip
from 30ns to 5ns.
This odd fix forward ported from legacy kernel.
Allows Rock Pi-S WiFi to operate at full speed.
* Set RK3308 I/O voltage domains before SDIO initializes
This patch moves responibility form the io-domain to the pinctrl driver because
the io-domain driver is probed after the SDIO devices are discovered.
This was causing multiple SDIO I/O failures during boot.
A new pinctrl property is added:
io-1v8-domains
is a u32 interpreted as a bit mask where each set bit corresponds to
a 1.8V I/O domain (as opposed to the default of 3.3V for I/O)
The mask is writted to the RK3308_SOC_CON0 GRF register
(once) when the pinctrl driver starts
The default mask is 0x10 where only I/O domain 4 runs at 1.8V
This is necessary for the RockPI-S to run the SDIO clock at high (50Mhz) speed
* align whitespace
* factored rk3308bs overlays out up sdio speedup patch
* factored dts for RK3308 iodomains and pinctrl patches out of speedup patch
* remains of sdio speedup patch merely add iodomains support for rk3308
* factored rockpis dts modification out from rk3308 io voltage domains
replaced rk3308 support from iodomains with
new io-voltage-domains property added to pinctrl
io-voltage-domains specific to rk3308 for now, others SOCs may be added later.
* add sequence numbering to names of rk3308 patches
* corrected tab alignment
* Add ssv6051p wifi driver for rockchip64 current and edge kernel
* also reorders and tidies device tree overlays for rk3318-box
* increase ssv6051 sdio bus to 50MHz in the driver
