- Armbian already had all the FIP-magic needed, just use it.
- Introduce USE_ODROID_UBOOT with a list of branches that use Odroid's 2015 u-boot
- this is mostly in preparation for non-Odroid G12B/meson64 boards (Khadas VIM3...)
- In case $BRANCH is listed in USE_ODROID_UBOOT:
- use BOOTCONFIG_ODROID and BOOTSCRIPT_ODROID from board.conf
- build 2015 u-boot just like before
- Small hack into boot-meson64.cmd to handle u-boot vs kernel: n2_plus vs n2-plus DTB/FDT naming mismatch
- overrides the default $fdtfile based on $variant
- armbianEnv still has final say if $fdtfile is set there (it isn't for n2/n2plus)
- Extra:
- remove unused n2-mainline bootscript (maybe from a previous try?)
- comments about FIP trees being identical across N2/N2Plus and C4/HC4 families so no future time wastage
- only set CPUMIN/CPUMAX/GOVERNOR in meson64_common.inc if not already set by the board.conf
- Add some ${bootargs} debugging to mainline/default boot-meson64.cmd
Signed-off-by: Ricardo Pardini <ricardo@pardini.net>
* cleanup add vim3l
* Add Khadas edge config
* Add Khadas edge sources definitions. It boots
* Change configuration to maximised model
* Adjust build configs
* witch to case statement for meson x11 config
* push vim1 naming
* Booting VIM2 with khadas prebuild u-boot
Can load from an empty eMMC, can be installed to eMMC via nand-sata-install
* Add Vim1 and move 1 and 2 to supported. VIM1 is not tested yet.
* Enable full featured desktop with 3D for khadas vim 1 and vim2
* Update meson64_common.inc
Co-authored-by: Igor Pecovnik <igor.pecovnik@gmail.com>
* Updated kernel/u-boot for MCIMX7SABRE board
Supporing 'current' and 'legacy' branches for MCIMX7SABRE board
current branch:
u-boot: imx_v2020.04_5.4.70_2.3.0
kernel: imx_5.4.70_2.3.0
legacy branch:
u-boot: imx_v2018.03_4.14.98_2.0.0_ga
kernel: imx_4.14.98_2.0.0_ga
* Update kernel config with few additional options like zram, bonding, ... just a few to keep minimum consistency over kernels.
Co-authored-by: Igor Pecovnik <igor.pecovnik@gmail.com>
* VENDOR, rock-pi-n10, RM_LIST for armbian-config/zsh
VENDOR parameter in configuration
zsh is the best of course...
Static MAC for networkd
ROCK Pi N10 (Radxa) - Initial support, knwon bugs:
- Problem with poweroff (kernel panic).
- DeviceTree is not fully verified, I suspect missing and unnecessary
entries.
- No support for NPU
- u-boot without NVME support
- I have doubts if I chose the right preboot loader for RK3399Pro, NPU
and installed DDR memory.
* New RK3399Pro boot preloaders.
* rootfs checksum, DEBOOTSTRAP_LIST fix, output.log fix
Repaired checksum for rootfs
Added use PACKAGE_LIST_RM to purge DEBOOTSTRAP_LIST
Better logging to output.log
Fix for new host distribution detection (ie Debian Bullseye).
ubootdebs as new cleaning option
Adds Xilinx Bootgen tools to build environment (alongside sunxi-tools, etc ..)
Adds new SoC family Zynq (7000 series, not MP/UltraScale)
Adds new board Avnet MicroZed
* add Jetson Nano
* Update jetson-nano.conf
* Update targets.conf
* Add better description
* Adjust config - try to enable ZRAM
* Packaging patch not needed
* Extlinux was solved in other commit
* Move board to CSC for now
Co-authored-by: Igor Pečovnik <igorpecovnik@users.noreply.github.com>
Co-authored-by: Igor Pecovnik <igor.pecovnik@gmail.com>
* Bump rockchip DEV 32b to 5.11.y
* Move mvebu64 DEV to 5.11.y
* Move Rockchip64 DEV to 5.11.y
Disabling general-rkvdec_nv15.patch - need more attention
* Add Meson DEV / Odroid C1
* Move OdroidXU4 DEV to tobetter's 5.11.y branch
* Bump sunxi DEV to 5.11.y
* Bump mvebu DEV to 5.11.y
* Enable RTC (hym8563) for Station P1 in mainline (renaming DT in process)
* Switch Station P1 to rockchip64
* Fix linking for Station P1 device tree in legacy
* Document board config variables
Add brief descriptions for board config variables which lack an explanation
* Emphasize deprecated variables in board config README
"next" is deprecated with AR-8.
Add "(deprecated)" to the end of description for more clarity.
* Update board config variable descriptions
Remove descriptions which are related to deprecated branches.
Remove descriptions which are not relevant for board configuration.
Change description of BOOT_FDT_FILE variable with a more elaborate one.
* Update board config variable descriptions
Even though they are not used frequently;
add description for "BOOTCONFIG_LEGACY" and "BOOTCONFIG_CURRENT".
* Add support for ZSH / TMUX / oh-my-zsh
* Selecting default shell at 1st run
* Install ZSH by default except on minimal image
* Lets rather create armbian-zsh package
* - fix remaining ZSH problems
- add systemd timer to remove default desktop autologin feature
- change DESKTOP_AUTOLOGIN to disabled by default
* Few small improvements
* Oneliner for revering all users back to BASH if package is uninstalled
* Properly escape variables
* Fixing chmod
* More cryptic awk magic to fix permissions for all normal users that are getting zsh magic
* Add WIP support for Orangepi Zero 2
* squeeze H616 patches into sunxi-dev
* Update linux-sunxi64-dev.config
* H616: Limit CPUMAX
* Enable DEV only
* H616: remove patches from sunxi-current
* H616: apply new patchset
Co-authored-by: EvilOlaf <werner@armbian.de>
Co-authored-by: Werner <EvilOlaf@users.noreply.github.com>
* sunxi: kernel: current/dev: enable sun6i-csi and disable LL debug on UART0
The former is useful on some boards, e.g. PineCube.
The latter blocks boards that do not utilize UART0 from booting.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
* sunxi: add new family sun8i-v3s
This family is intended for boards with V3/V3s/S3/S3L chips and low
DRAM capacity.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
* sunxi: add PineCube board
This board features Sochip S3 SoC (Allwinner V3 die + co-packaged 128MiB
DRAM), and an OmniVision OV5640 camera is shipped with the board.
Add support for it. It could be used as an IP camera then.
Kernel support is only added to current/dev branch, with dev just using
mainline-merged DT and current using backported DT from 5.10-rc.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
* sunxi: kernel: current/dev: add V3s OHCI/EHCI nodes
These are needed for USB host on V3s boards to work.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
* update fancontrol configuration
* Enable network activity led, default to eth0
* Do not disable auto poweron on power loss event
* Added UPS timer
Provide timer to poweroff system after 600 s (10 minutes) of power loss
event. If power restored within that time window, cancel the timer.
* Use different service for legacy
LK 4.4 does not have ledtrig-netdev, so it will cause the service to
fail.
* Use 10m instead 600 seconds in UPS timer
Systemd time can use m suffix for minutes. Use this to make it easier to
read.
