- remove add-board-makefile Patch
- remove `overlay-y` Makefile patch
- add note to the 6.1 version: Makefile autopatcher can't be enabled for 6.1, since the armhf move to subdirs only landed in 6.5-rc1
> Based on AmazingFate's kernel DT and Kwiboo's `rk3568-2023.10`
Tested with a OrangePi 3B 4GB v1.1:
- SD-card boot
- eMMC boot
- SPI Flash boot
- chip is XMC `XM25QU128CWIQ`, not `W25Q256JWEIQ` listed in schematics
- PCIe/NVMe
- Ethernet has stable MAC
- can boot both edge (mainline) and legacy (vendor rk 5.10) kernels
- USB in uboot is untested
- UMS untested (I lost my A-to-A otg cable)
BPI-CM4: Add support for the waveshare cm4-io-base-b
https://www.waveshare.com/wiki/CM4-IO-BASE-B
BPI-CM4: Enable usb support on waveshare baseboards via overlay
BPI-SM1: Removed UART_B overlay. Short of it being an available
option in the vendor kernel via overlay. I can not find any docs
to support why that is. I feel it is safer that we just remove it.
BPI-SM1: Add UART_A "pin-ctrl: cts rts"
Signed-off-by: Patrick Yavitz <pyavitz@xxxxx.com>
* update libreelec patches to latest bits
* rework some patches
* rework dtb patches due to new arch/arm/boot/dts layout
* fix led overlays due to idiot u-boot dtbo bug
Upstream code has trickled down into 6.5.y, so adjust patching
accordingly.
Signed-off-by: Patrick Yavitz <pyavitz@xxxxx.com>
Co-authored-by: Patrick Yavitz <pyavitz@xxxxx.com>
Restore 'less than or equal' match of clocks that was lost in patch transition from 6.3 to 6.4:
ttps://github.com/armbian/build/blob/6d981baba68699b0c6ada476704556e11dd661bc/patch/kernel/archive/rockchip64-6.3/rk356x-vop2-support.patch#L333
6d981baba6/patch/kernel/archive/rockchip64-6.4/rk356x-vop2-support.patch (L333)
This is just a cosmetic change. Patches have been consolidated
into one patch within each corresponding linux version directory.
Added: linux-6.6 (RC-1)
Removed: linux-6.2/6.3
Signed-off-by: Patrick Yavitz <pyavitz@xxxxx.com>
Co-authored-by: Patrick Yavitz <pyavitz@xxxxx.com>
Also added some cleanup fixes to silence some of the compiler warnings,
fixes for issues during inserting and removing xradio module and fixes
for possible data corruption on vmmaped stack.
All of these fixes were taken from https://github.com/fifteenhex/xradio
* patch: misc: rtw88: wireless-next: 2023-08-25
Updated: 6.1 / 6.4
Added: 6.5
For doc sake, this update makes 6.1 slightly differrent than 6.4 and
6.5 in one particular area of main.c.
As shown here:
7746e2fa87
6.1 requires we use del_timer_sync, where the above releases use
timer_delete_sync.
Tested-on: ODROID-C4 X96-AIR BPI-CM4 (linux 6.x.y)
Signed-off-by: Patrick Yavitz <pyavitz@xxxxx.com>
* driver_rtw88: `linux-version compare "${version}" ge 6.1`
Suggested-by: @viraniac
Signed-off-by: Patrick Yavitz <pyavitz@xxxxx.com>
---------
Signed-off-by: Patrick Yavitz <pyavitz@xxxxx.com>
Co-authored-by: Patrick Yavitz <pyavitz@xxxxx.com>
After we bumped u-boot to version v2022.10, a couple of boards
stopped booting because the CONFIG_SPL_STACK value used in our
u-boot config was too low for that SOC. This change drops explicit
CONFIG_SPL_STACK defination from the affected boards.
The boards confirmed to have the issues were Orange Pi 3 LTS and
NanoPi Neo Black2 but I suspect that NanoPi K1 plus is also affected
hence similar change is done for that as well
* dts: amlogic: meson-g12b-bananapi-cm4: switch to enable-gpios
The recommended name for enable GPIOs property in regulator-gpio is
enable-gpios. This is also required by bindings:
meson-g12b-bananapi-cm4-cm4io.dtb: regulator-vddio-c: Unevaluated properties are not allowed ('enable-gpio' was unexpected)
Signed-off-by: Patrick Yavitz <pyavitz@xxxxx.com>
* board-bananapi-cm4-switch-to-enable-gpios: `text formatting correction`
Apparently the builder did care for the original.
Signed-off-by: Patrick Yavitz <pyavitz@xxxxx.com>
---------
Signed-off-by: Patrick Yavitz <pyavitz@xxxxx.com>
Co-authored-by: Patrick Yavitz <pyavitz@xxxxx.com>
- using Kwiboo's `rk3568-2023.10` branch with BINMAN-handled blobs
- patches (defconfig unless indicated):
- boot usb first (rockchip-common)
- blink leds & keep red one one on preboot; reset SPI env once after deinfesting from Petitboot
- change usb_host0_xhci to otg (u-boot dtsi)
- enable DM_GADGET, UMS 🔥 and RockUSB
- **usage instructions**:
- build & burn image to SD card
- insert SD card into board
- **hold the recovery (RCY) button** and power on the board
- watch board boot
- **de-infest Petitboot**: use `armbian-install` to install bootloader to MTD
- if you don't, you'll need to hold the recovery button every boot
- optionally: use `armbian-install` to install OS to eMMC/NVMe/USB
- power-off board
- remove SD card (new u-boot always boots SD first!)
- boot into your newly de-infested machine
- boot order: USB, SD, MMC, NVME, SCSI
- de-infested machine can now boot (directly) from USB/SATA/NVMe, possibly via EFI:
- Armbian UEFI-arm64
- Fedora 38 aarch64
- HASSOS for ODROID-M1
- Talos arm64
- others...
- extra: new u-boot by Kwiboo (with GMAC patches) gives us stable MAC address
- although it is based on cpuid#, doesn't match the HK sticker on the board
- run `fw_setenv ethaddr XX:XX:XX:XX:XX:XX` to change eth addr in SPI flash environment if needed
- `odroidm1`: update DDR/BL31 blobs (this depends on https://github.com/armbian/rkbin/pull/20)
Backport DTS/DTSI changes from linux-6.4.y to 6.1.y
Add meson64-reboot driver to all boards
Add board: ODROID N2L
Add uart_A uart_AO_B uart_B uart_C where appropriate
U-Boot v2023.07.02: ODROID N2/N2L/N2Plus/C4
Meson64-reboot driver: (source: tobetter)
While the current meson64-reboot driver is cleaner and doesn't
depend on modding other kernel sources, its functionality leaves
much to be desired. One example can be found in the ODROID C4.
Using the current driver, the board will not properly power off,
leaving the POWER LED still on. The new driver powers off the unit
completely.
Fan control: (ODROID N2L/N2PLus)
Added service and script for controlling the trip point.
fanctrl: arguments: 65 55 45 35 25 menu run
┌──┤ Fan Control ├──┐
│ │
│ 6) 65°C │
│ 5) 55°C │
│ 4) 45°C │
│ 3) 35°C │
│ 2) 25°C │
│ E) Exit .. │
│ │
│ │
│ <Ok> │
│ │
└───────────────────┘
NOTES: (N2L/HC4): I do not own the units so I can't run tests.
Signed-off-by: Patrick Yavitz <pyavitz@xxxxx.com>
