Added ayn-odin2mini board config;

Fixed WITH_GRUB flag;

config/boards/ayn-odin2.csc

@@ -13,9 +13,9 @@ declare -g BOARD_FIRMWARE_INSTALL="-full"
 declare -g DESKTOP_AUTOLOGIN="yes"
 
 # Check to make sure variants are supported
-declare -g VALID_BOARDS=("ayn-odin2" "ayn-odin2portal" "ayn-thor")
+declare -g VALID_BOARDS=("ayn-odin2" "ayn-odin2portal" "ayn-odin2mini" "ayn-thor")
 
-declare -g WITH_GRUB="no"
+declare -g WITH_GRUB="${WITH_GRUB:-no}"
 
 if [[ ! " ${VALID_BOARDS[*]} " =~ " ${BOARD} " ]]; then
 	exit_with_error "Error: Invalid board '$BOARD'. Valid options are: ${VALID_BOARDS[*]}" >&2

config/boards/ayn-odin2mini.csc

@@ -0,0 +1 @@
+source "${SRC}/config/boards/ayn-odin2.csc"

packages/bsp/ayn-odin2mini/AYN-Odin2.conf

@@ -0,0 +1,31 @@
+# Use case configuration for AYN Odin2
+# Author: Teguh Sobirin <teguh@sobir.in>
+
+Syntax 4
+
+SectionUseCase."HiFi" {
+	File "/AYN/Odin2/HiFi.conf"
+	Comment "HiFi quality Music."
+}
+
+BootSequence [
+	cset "name='RX_RX0 Digital Volume' 84"
+	cset "name='RX_RX1 Digital Volume' 84"
+	cset "name='HPHL Volume' 20"
+	cset "name='HPHR Volume' 20"
+	cset "name='ADC2 Volume' 10"
+]
+
+LibraryConfig.remap.Config {
+
+	ctl.default.map {
+		"name='HP Volume'" {
+			"name='HPHL Volume'".vindex.0 0
+			"name='HPHR Volume'".vindex.1 0
+		}
+	}
+}
+
+Include.card-init.File "/lib/card-init.conf"
+Include.ctl-remap.File "/lib/ctl-remap.conf"
+Include.wcd-init.File "/codecs/wcd938x/init.conf"

packages/bsp/ayn-odin2mini/HiFi.conf

@@ -0,0 +1,91 @@
+# Use case configuration for AYN Odin2
+# Author: Teguh Sobirin <teguh@sobir.in>
+
+SectionVerb {
+	EnableSequence [
+		cset "name='PRIMARY_MI2S_RX Audio Mixer MultiMedia1' 1"
+		cset "name='RX_CODEC_DMA_RX_0 Audio Mixer MultiMedia2' 1"
+		cset "name='DISPLAY_PORT_RX_0 Audio Mixer MultiMedia2' 0"
+		cset "name='MultiMedia3 Mixer TX_CODEC_DMA_TX_3' 1"
+	]
+
+	DisableSequence [
+		cset "name='PRIMARY_MI2S_RX Audio Mixer MultiMedia1' 0"
+		cset "name='RX_CODEC_DMA_RX_0 Audio Mixer MultiMedia2' 0"
+		cset "name='DISPLAY_PORT_RX_0 Audio Mixer MultiMedia2' 0"
+		cset "name='MultiMedia3 Mixer TX_CODEC_DMA_TX_3' 0"
+	]
+
+	Value {
+		TQ "HiFi"
+	}
+}
+
+SectionDevice."Speaker" {
+	Comment "Speaker playback"
+
+	Value {
+		PlaybackPriority 150
+		PlaybackPCM "hw:${CardId},0"
+		PlaybackChannels 2
+	}
+}
+
+SectionDevice."Headphones" {
+	Comment "Headphones Playback"
+
+	Include.wcdhpe.File "/codecs/wcd938x/HeadphoneEnableSeq.conf"
+	Include.wcdhpd.File "/codecs/wcd938x/HeadphoneDisableSeq.conf"
+	Include.rxmhpe.File "/codecs/qcom-lpass/rx-macro/HeadphoneEnableSeq.conf"
+	Include.rxmhpd.File "/codecs/qcom-lpass/rx-macro/HeadphoneDisableSeq.conf"
+
+	Value {
+		PlaybackPriority 200
+		PlaybackPCM "hw:${CardId},1"
+		PlaybackMixer "default:${CardId}"
+		PlaybackMixerElem "HP"
+		PlaybackChannels 2
+		JackControl "Headphone Jack"
+		JackHWMute "Speaker"
+	}
+}
+
+SectionDevice."Headset" {
+	Comment "Headphone Microphone"
+
+	Include.wcdmice.File "/codecs/wcd938x/HeadphoneMicEnableSeq.conf"
+	Include.wcdmicd.File "/codecs/wcd938x/HeadphoneMicDisableSeq.conf"
+	Include.txmhpe.File "/codecs/qcom-lpass/tx-macro/SoundwireMic1EnableSeq.conf"
+	Include.txmhpd.File "/codecs/qcom-lpass/tx-macro/HeadphoneMicDisableSeq.conf"
+
+	Value {
+		CapturePriority 200
+		CapturePCM "hw:${CardId},2"
+		CaptureMixerElem "ADC2"
+		CaptureChannels 1
+		JackControl "Mic Jack"
+	}
+}
+
+SectionDevice."DisplayPort" {
+	Comment "DisplayPort playback"
+
+	EnableSequence [
+		cset "name='PRIMARY_MI2S_RX Audio Mixer MultiMedia1' 0"
+		cset "name='RX_CODEC_DMA_RX_0 Audio Mixer MultiMedia2' 0"
+		cset "name='DISPLAY_PORT_RX_0 Audio Mixer MultiMedia2' 1"
+	]
+
+	DisableSequence [
+		cset "name='PRIMARY_MI2S_RX Audio Mixer MultiMedia1' 1"
+		cset "name='DISPLAY_PORT_RX_0 Audio Mixer MultiMedia2' 0"
+		cset "name='RX_CODEC_DMA_RX_0 Audio Mixer MultiMedia2' 1"
+	]
+
+	Value {
+		PlaybackPriority 100
+		PlaybackPCM "hw:${CardId},1"
+		JackControl "DP0 Jack"
+		JackHWMute "Speaker"
+	}
+}

packages/bsp/ayn-odin2mini/LinuxLoader.cfg

@@ -0,0 +1,58 @@
+#
+# Configure the LinuxLoader settings
+#
+
+[LinuxLoader]
+
+# Controls on-screen logging
+# This setting can persist without config file or sdcard being present
+Debug = true
+
+# Boot target. Can be one of the following:
+# "default" (ABL default)
+# "Linux" (direct Linux Image load)
+# "EFI"
+# "UEFI Shell" (will execute startup.nsh automatically if found on any FAT partition)
+# "Mass Storage" (will mount the UFS LUN specified below as mass storage)
+Target = "default"
+
+# Default UFS LUN to mount as mass storage
+# Allowed values: 0, 1, 2, 3, 4, 5
+MassStorageLUN = 0
+
+# Volume up boot target. Can be one of the following:
+# "BDS Menu" (will enter the UEFI boot menu provided by Qualcomm, don't touch anything there unless you know what you are doing!)
+# "UEFI Shell" (will execute startup.nsh automatically if found on any FAT partition)
+# "recovery"
+# "Linux"
+DefaultVolUp = "Linux"
+
+# Setting this to *true* will enable USB Host mode in UEFI
+# This might be useful if you want to play with UEFI.
+# Note that you will need an externally powered type-C hub to connect USB devices. (at least for now)
+UsbHostMode = false
+
+# Controls hypervisor UART enablement
+#
+# Setting *true* here will force enable the hypervisor UART
+# Setting *false* here will force disable the hypervisor UART
+# Removing this line will avoid changing the default behavior
+# Please leave it to *false* unless you know what you are doing
+HypUartEnable = false
+
+# Controls display hardware status during exit boot services
+#
+# The dispcc driver from mainline Linux kernel has a bug, which
+# prevents the display hardware from initializing properly if
+# the display hardware is not disabled before exiting boot services.
+#
+# Set this to *true* if you are trying to boot a mainline kernel.
+DisableDisplayHW = true
+
+[Linux]
+# Accept both gzipped and non-gzipped kernel images
+Image = "Image"
+initrd = "initrd.img-INITRD_PLACEHOLDER"
+devicetree = "dtb/qcom/qcs8550-ayn-odin2mini.dtb"
+cmdline = "clk_ignore_unused pd_ignore_unused arm64.nopauthfbcon=rotate:3 console=ttyMSM0,115200n8 root=UUID=UUID_PLACEHOLDER"
+

packages/bsp/ayn-odin2mini/zz-update-abl-kernel

@@ -0,0 +1,20 @@
+#!/bin/bash
+set -ex
+new_rootfs_image_uuid=$(sed -e 's/^.*root=UUID=//' -e 's/ .*$//' < /proc/cmdline)
+gzip -c /boot/vmlinuz-*-sm8550-arm64 > /tmp/Image.gz
+
+cat /tmp/Image.gz /usr/lib/linux-image-*-sm8550-arm64/qcom/qcs8550-ayn-odin2-hypdtbo.dtb > /tmp/Image.gz-dtb
+
+source /boot/armbianEnv.txt
+/usr/bin/mkbootimg \
+        --kernel /tmp/Image.gz-dtb \
+        --ramdisk /boot/initrd.img-*-sm8550-arm64 \
+        --base 0x0 \
+        --second_offset 0x00f00000 \
+        --cmdline "clk_ignore_unused pd_ignore_unused panic=30 audit=0 allow_mismatched_32bit_el0 rw mem_sleep_default=s2idle root=UUID=${new_rootfs_image_uuid}" \
+        --kernel_offset 0x8000 \
+        --ramdisk_offset 0x1000000 \
+        --tags_offset 0x100 \
+        --pagesize 4096 \
+        -o /boot/armbian-kernel.img
+rm -f /tmp/Image.gz /tmp/Image.gz-dtb