diff --git a/config/fex/bananapim2plus.fex b/config/fex/bananapim2plus.fex index fa5e79237c..9997b07b48 100644 --- a/config/fex/bananapim2plus.fex +++ b/config/fex/bananapim2plus.fex @@ -1,30 +1,76 @@ +;H3 dolphin-p1 board application +;H3 dolphin-p1 board application +;--------------------------------------------------------------------------------------------------------- +; 说明： 脚本中的字符串区分大小写，用户可以修改"="后面的数值，但是不要修改前面的字符串 +; 描述gpio的形式：Port:端口+组内序号<功能分配><内部电阻状态><驱动能力><输出电平状态> +;--------------------------------------------------------------------------------------------------------- + [product] version = "100" machine = "bananapi-m2-plus" +;--------------------------------------------------------------------------------------------------------- +; eraseflag - 1 erase data partition, 0 - do not erase data partition +; next_work - action after burn, 0x0 by config, 0x1, normal, 0x2 reboot 0x3 ,shutdown,0x4 reupdate ,0x5 boot +;--------------------------------------------------------------------------------------------------------- [platform] debug_mode = 1 -eraseflag = 1 +eraseflag = 1 next_work = 2 +;---------------------------------------------------------------------------------- +;[target] system bootup configuration +;boot_clock = CPU boot frequency, Unit: MHz +;storage_type = boot medium, 0-nand, 1-card0, 2-card2, -1(defualt)auto scan +;---------------------------------------------------------------------------------- [target] -boot_clock = 1008 -storage_type = -1 +boot_clock = 1008 +storage_type = -1 +;--------------------------------------------------------------------------------- +; uboot key detect enable +; 当keyen_flag = 1 时，支持按键检测 +; 当keyen_flag = 0 时，不支持 +;--------------------------------------------------------------------------------- [key_detect_en] keyen_flag = 0 +;--------------------------------------------------------------------------------- +;"一键进烧写功能"的按键值配置，按住位于min~max范围内的按键都可以强制进烧写 +; fel_key_max用于配置按键的最大键值 +; fel_key_min用于配置按键的最小键值 +;--------------------------------------------------------------------------------- [fel_key] -fel_key_max = 7 -fel_key_min = 2 +fel_key_max =07 +fel_key_min =02 +;---------------------------------------------------------------------------------- +;card boot +;logical_start用于配置启动卡上mbr的位置相对于SD卡sector 0的偏移，单位为sector(512byte) +;sprite_gpio0用于配置卡量产时指示灯所用的gpio +;---------------------------------------------------------------------------------- +;------------------------------------------------------------------------------- +; sprite_work_delay : +; sprite_err_delay : +; sprite_gpio0 ： 卡量产、一键recovery状态指示灯 +; next_work ： 卡量产完成，工作状态(默认关机) +;------------------------------------------------------------------------------- [card_boot] -logical_start = 40960 -sprite_work_delay = 500 -sprite_err_delay = 200 -sprite_gpio0 = port:PL10<1> -next_work = 3 +logical_start = 40960 +sprite_work_delay = 500 +sprite_err_delay = 200 +sprite_gpio0 = port:PL10<1> +next_work = 3 +;--------------------------------------------------------------------------------- +; used : 1: used this config, 0: not +; start_type : 1: start system directly when power supply, 0: wait IR/KEY to power on +; irkey_used : 1: ir key used, 0: not +; pmukey_used: 1: physical button used, 0: not +; pmukey_num : the index of gpio, only support PL +; led_power : 1: light, 0: off, the control gpio is PL10 +; led_state : 1: light, 0: off, default is 0 +;--------------------------------------------------------------------------------- [box_start_os] used = 1 start_type = 1 @@ -34,226 +80,307 @@ pmukey_num = 30 led_power = 0 led_state = 0 +;------------------------------------------------------------------------------- +; boot阶段上电初始化GPIO +; used :模块使能端 置1：开启模块 置0：关闭模块 +; gpiox ：上电初始化gpio （名称自定，但不能重复，并且GPIO允许可以多个） +; PH06 : 系统显示LED GPIO +;------------------------------------------------------------------------------- [boot_init_gpio] -used = 1 -gpio0 = port:PL10<1><1> -gpio1 = port:PA15<1><1> +used = 1 +gpio0 = port:PL10<1><1> +gpio1 = port:PA15<1><1> +;---------------------------------------------------------------------------------- +; used: 模块使能端 1：开启模块 0：关闭模块 +; mode: 模式选择 1：一键进入OTA升级 2：一键恢复（通过sysrecovery分区来恢复） 其他值：无效 +; recovery_key ： 按键配置 （例如：recovery_key= port:PH16<0>） +;---------------------------------------------------------------------------------- [recovery_para] -used = 1 -mode = 2 +used = 1 +mode = 2 recovery_key = port:PL03<0> + +;--------------------------------------------------------------------------------------------------------- +; if 1 == standby_mode, then support super standby; +; else, support normal standby. +;--------------------------------------------------------------------------------------------------------- [pm_para] -standby_mode = 1 +standby_mode = 1 [card0_boot_para] -card_ctrl = 0 +card_ctrl = 0 card_high_speed = 1 -card_line = 4 -sdc_d1 = port:PF00<2><1><2> -sdc_d0 = port:PF01<2><1><2> -sdc_clk = port:PF02<2><1><2> -sdc_cmd = port:PF03<2><1><2> -sdc_d3 = port:PF04<2><1><2> -sdc_d2 = port:PF05<2><1><2> +card_line = 4 +sdc_d1 = port:PF00<2><1><2> +sdc_d0 = port:PF01<2><1><2> +sdc_clk = port:PF02<2><1><2> +sdc_cmd = port:PF03<2><1><2> +sdc_d3 = port:PF04<2><1><2> +sdc_d2 = port:PF05<2><1><2> [card2_boot_para] -card_ctrl = 2 +card_ctrl = 2 card_high_speed = 1 -card_line = 8 -sdc_cmd = port:PC06<3><1><2> -sdc_clk = port:PC05<3><1><2> -sdc_d0 = port:PC08<3><1><2> -sdc_d1 = port:PC09<3><1><2> -sdc_d2 = port:PC10<3><1><2> -sdc_d3 = port:PC11<3><1><2> -sdc_d4 = port:PC12<3><1><2> -sdc_d5 = port:PC13<3><1><2> -sdc_d6 = port:PC14<3><1><2> -sdc_d7 = port:PC15<3><1><2> -sdc_2xmode = 1 -sdc_ddrmode = 1 +card_line = 8 +sdc_cmd = port:PC06<3><1><2> +sdc_clk = port:PC05<3><1><2> +sdc_d0 = port:PC08<3><1><2> +sdc_d1 = port:PC09<3><1><2> +sdc_d2 = port:PC10<3><1><2> +sdc_d3 = port:PC11<3><1><2> +sdc_d4 = port:PC12<3><1><2> +sdc_d5 = port:PC13<3><1><2> +sdc_d6 = port:PC14<3><1><2> +sdc_d7 = port:PC15<3><1><2> +sdc_2xmode = 1 +sdc_ddrmode = 1 [twi_para] -twi_port = 0 -twi_scl = port:PA11<2> -twi_sda = port:PA12<2> +twi_port = 0 +twi_scl = port:PA11<2> +twi_sda = port:PA12<2> [uart_para] uart_debug_port = 0 -uart_debug_tx = port:PA04<2><1> -uart_debug_rx = port:PA05<2><1> +uart_debug_tx = port:PA04<2><1> +uart_debug_rx = port:PA05<2><1> [force_uart_para] -force_uart_port = 0 -force_uart_tx = port:PF02<3><1> -force_uart_rx = port:PF04<3><1> +force_uart_port = 0 +force_uart_tx = port:PF02<3><1> +force_uart_rx = port:PF04<3><1> [jtag_para] -jtag_enable = 0 -jtag_ms = port:PA00<3> -jtag_ck = port:PA01<3> -jtag_do = port:PA02<3> -jtag_di = port:PA03<3> +jtag_enable = 0 +jtag_ms = port:PA00<3> +jtag_ck = port:PA01<3> +jtag_do = port:PA02<3> +jtag_di = port:PA03<3> [clock] -pll_video = 297 -pll_ve = 402 -pll_periph0 = 600 -pll_gpu = 576 -pll_periph1 = 600 -pll_de = 864 +pll_video = 297 +pll_ve = 402 +pll_periph0 = 600 +pll_gpu = 576 +pll_periph1 = 600 +pll_de = 864 +;***************************************************************************** +;sdram configuration +; +; dram_tpr7[31:31]=1, use gpio type to detect dram type and +; dram_tpr7[31:31]=0, not use gpio type to detect dram type. +; +; if set ddr type auto detect, use dram_tpr7 to set dram clk. +; for example: if dram_tpr13[13:13] = 1, it use +; dram_tpr7[29:20] to set lpddr2 clk, +; dram_tpr7[19:10] to set lpddr3 clk, +; dram_tpr7[9:0] to set ddr3 or ddr3l clk. +;***************************************************************************** [dram_para] -dram_clk = 672 -dram_type = 3 -dram_zq = 0x3b3bfb -dram_odt_en = 1 -dram_para1 = 283377664 -dram_para2 = 0 -dram_mr0 = 6208 -dram_mr1 = 64 -dram_mr2 = 24 -dram_mr3 = 2 -dram_tpr0 = 0x48a192 -dram_tpr1 = 0x1c2418d -dram_tpr2 = 0x76051 -dram_tpr3 = 0x0 -dram_tpr4 = 0x0 -dram_tpr5 = 0x0 -dram_tpr6 = 0x64 -dram_tpr7 = 0x0 -dram_tpr8 = 0x0 -dram_tpr9 = 0x0 -dram_tpr10 = 0x0 -dram_tpr11 = 0x6aaa0000 -dram_tpr12 = 0x7979 -dram_tpr13 = 0x800800 +dram_clk = 672 +dram_type = 3 +dram_zq = 0x3b3bfb +dram_odt_en = 0x1 +dram_para1 = 0x10E40000 +dram_para2 = 0x0000 +dram_mr0 = 0x1840 +dram_mr1 = 0x40 +dram_mr2 = 0x18 +dram_mr3 = 0x2 +dram_tpr0 = 0x0048A192 +dram_tpr1 = 0x01C2418D +dram_tpr2 = 0x00076051 +dram_tpr3 = 0 +dram_tpr4 = 0 +dram_tpr5 = 0 +dram_tpr6 = 100 +dram_tpr7 = 0 +dram_tpr8 = 0 +dram_tpr9 = 0 +dram_tpr10 = 0 +dram_tpr11 = 0x6aaa0000 +dram_tpr12 = 0x7979 +dram_tpr13 = 0x800800 +;---------------------------------------------------------------------------------- +;os life cycle para configuration +;---------------------------------------------------------------------------------- +;--------------------------------------------------------------------------------------------------------- +; wakeup_src_para: +; sometimes, u would like to add more wakeup src in standby mode, these para will be +; help; +; u need to make sure the standby mode support the wakeup src. Also, some hw +; condition must be guaranteed. +; including: +; cpu_en: power on or off. +; 1: mean power on +; 0: mean power off +; cpu_freq: indicating lowest freq. unit is Mhz; +; dram selfresh_en: selfresh or not. +; 1: enable enter selfresh +; 0: disable enter selfresh +; dram_pll: if not enter selfresh, indicating lowest freq. unit is Mhz; +; wakeup_src: to make the scenario work, the wakeup src is needed. +;--------------------------------------------------------------------------------------------------------- [wakeup_src_para] -cpu_en = 0 -cpu_freq = 48 -pll_ratio = 273 -dram_selfresh_en = 1 -dram_freq = 36 -wakeup_src0 = -wakeup_src_wl = port:PG10<4><0> +cpu_en = 0 +cpu_freq = 48 +; (cpu:apb:ahb) +pll_ratio = 0x111 +dram_selfresh_en = 1 +dram_freq = 36 +wakeup_src0 = +wakeup_src_wl = port:PG10<4><0> +;wakeup_src_bt = port:PL03<6><0> +;---------------------------------------------------------------------------------- +;i2c configuration +;---------------------------------------------------------------------------------- [twi0] -twi_used = 1 -twi_scl = port:PA11<2> -twi_sda = port:PA12<2> +twi_used = 1 +twi_scl = port:PA11<2> +twi_sda = port:PA12<2> [twi1] -twi_used = 1 -twi_scl = port:PA18<3> -twi_sda = port:PA19<3> +twi_used = 1 +twi_scl = port:PA18<3> +twi_sda = port:PA19<3> [twi2] -twi_used = 0 -twi_scl = port:PE12<3> -twi_sda = port:PE13<3> +twi_used = 0 +twi_scl = port:PE12<3> +twi_sda = port:PE13<3> +;---------------------------------------------------------------------------------- +;uart configuration +;uart_type --- 2 (2 wire), 4 (4 wire), 8 (8 wire, full function) +;---------------------------------------------------------------------------------- [uart0] -uart_used = 1 -uart_port = 0 -uart_type = 2 -uart_tx = port:PA04<2><1> -uart_rx = port:PA05<2><1> +uart_used = 1 +uart_port = 0 +uart_type = 2 +uart_tx = port:PA04<2><1> +uart_rx = port:PA05<2><1> [uart1] -uart_used = 1 -uart_port = 1 -uart_type = 4 -uart_tx = port:PG06<2><1> -uart_rx = port:PG07<2><1> -uart_rts = port:PG08<2><1> -uart_cts = port:PG09<2><1> +uart_used = 1 +uart_port = 1 +uart_type = 4 +uart_tx = port:PG06<2><1> +uart_rx = port:PG07<2><1> +uart_rts = port:PG08<2><1> +uart_cts = port:PG09<2><1> [uart2] -uart_used = 1 -uart_port = 2 -uart_type = 4 -uart_tx = port:PA00<2><1> -uart_rx = port:PA01<2><1> -uart_rts = port:PA02<2><1> -uart_cts = port:PA03<2><1> +uart_used = 1 +uart_port = 2 +uart_type = 4 +uart_tx = port:PA00<2><1> +uart_rx = port:PA01<2><1> +uart_rts = port:PA02<2><1> +uart_cts = port:PA03<2><1> [uart3] -uart_used = 1 -uart_port = 3 -uart_type = 2 -uart_tx = port:PA13<3><1> -uart_rx = port:PA14<3><1> -uart_rts = port:PA15<3><1> -uart_cts = port:PA16<3><1> +uart_used = 1 +uart_port = 3 +uart_type = 2 +uart_tx = port:PA13<3><1> +uart_rx = port:PA14<3><1> +uart_rts = port:PA15<3><1> +uart_cts = port:PA16<3><1> +;---------------------------------------------------------------------------------- +;SPI controller configuration +;---------------------------------------------------------------------------------- [spi0] -spi_used = 1 -spi_cs_bitmap = 1 -spi_mosi = port:PC00<3> -spi_miso = port:PC01<3> -spi_sclk = port:PC02<3> -spi_cs0 = port:PC03<3><1> +spi_used = 1 +spi_cs_bitmap = 1 +spi_mosi = port:PC00<3> +spi_miso = port:PC01<3> +spi_sclk = port:PC02<3> +spi_cs0 = port:PC03<3><1> [spi1] -spi_used = 0 -spi_cs_bitmap = 1 -spi_cs0 = port:PA13<2><1> -spi_sclk = port:PA14<2> -spi_mosi = port:PA15<2> -spi_miso = port:PA16<2> +spi_used = 0 +spi_cs_bitmap = 1 +spi_cs0 = port:PA13<2><1> +spi_sclk = port:PA14<2> +spi_mosi = port:PA15<2> +spi_miso = port:PA16<2> +;---------------------------------------------------------------------------------- +;SPI device configuration +;---------------------------------------------------------------------------------- [spi_devices] spi_dev_num = 1 [spi_board0] -modalias = "spidev" -max_speed_hz = 33000000 -bus_num = 0 -chip_select = 0 -mode = 0 -full_duplex = 1 -manual_cs = 0 +modalias = "spidev" +max_speed_hz = 33000000 +bus_num = 0 +chip_select = 0 +mode = 0 +full_duplex = 1 +manual_cs = 0 +;---------------------------------------------------------------------------------- +;userspace gpio interface +; ** COMMENT THE PINS USED IN OTHER INTERFACES (I2C, SPI, 1-WIRE...) +;---------------------------------------------------------------------------------- [gpio_para] -gpio_used = 1 -gpio_num = 30 -gpio_pin_1 = port:PA12<1><0> -gpio_pin_2 = port:PA11<1><0> -gpio_pin_3 = port:PA06<1><0> -gpio_pin_4 = port:PA13<1><0> -gpio_pin_5 = port:PA14<1><0> -gpio_pin_6 = port:PA01<1><0> -gpio_pin_7 = port:PA16<1><0> -gpio_pin_8 = port:PA00<1><0> -gpio_pin_9 = port:PA03<1><0> -gpio_pin_10 = port:PC04<1><0> -gpio_pin_11 = port:PC00<1><0> -gpio_pin_12 = port:PC01<1><0> -gpio_pin_13 = port:PA02<1><0> -gpio_pin_14 = port:PC02<1><0> -gpio_pin_15 = port:PC03<1><0> -gpio_pin_16 = port:PC07<1><0> -gpio_pin_17 = port:PA19<1><0> -gpio_pin_18 = port:PA18<1><0> -gpio_pin_19 = port:PA07<1><0> -gpio_pin_20 = port:PA08<1><0> -gpio_pin_21 = port:PL02<1><0> -gpio_pin_22 = port:PA09<1><0> -gpio_pin_23 = port:PA10<1><0> -gpio_pin_24 = port:PL04<1><0> -gpio_pin_25 = port:PA16<1><0> -gpio_pin_26 = port:PA21<1><0> -gpio_pin_27 = port:PA20<1><0> -gpio_pin_28 = port:PL03<0><1> +gpio_used = 1 +gpio_num = 30 +gpio_pin_1 = port:PA12<1><0> +gpio_pin_2 = port:PA11<1><0> +gpio_pin_3 = port:PA06<1><0> +gpio_pin_4 = port:PA13<1><0> +gpio_pin_5 = port:PA14<1><0> +gpio_pin_6 = port:PA01<1><0> +gpio_pin_7 = port:PA16<1><0> +gpio_pin_8 = port:PA00<1><0> +gpio_pin_9 = port:PA03<1><0> +;gpio_pin_10 = port:PA15<1><0> +gpio_pin_10 = port:PC04<1><0> +gpio_pin_11 = port:PC00<1><0> +gpio_pin_12 = port:PC01<1><0> +gpio_pin_13 = port:PA02<1><0> +gpio_pin_14 = port:PC02<1><0> +gpio_pin_15 = port:PC03<1><0> +gpio_pin_16 = port:PC07<1><0> +gpio_pin_17 = port:PA19<1><0> +gpio_pin_18 = port:PA18<1><0> +gpio_pin_19 = port:PA07<1><0> +gpio_pin_20 = port:PA08<1><0> +gpio_pin_21 = port:PL02<1><0> +gpio_pin_22 = port:PA09<1><0> +gpio_pin_23 = port:PA10<1><0> +gpio_pin_24 = port:PL04<1><0> +gpio_pin_25 = port:PA16<1><0> +gpio_pin_26 = port:PA21<1><0> +gpio_pin_27 = port:PA20<1><0> +;gpio_pin_29 = port:PL10<1><1> +gpio_pin_28 = port:PL03<0><1> [leds_para] leds_used = 1 red_led = port:PL10<1><1> red_led_active_low = 0 +;---------------------------------------------------------------------------------- +;thermal configuration +;ths_trip_count : temperature trigger number +;ths_trip_0 : first temperature trigger +;ths_trip_1 : second temperature trigger +;ths_trip_2 : third temperature trigger, when upto this temperature, system shutdown +;ths_trip_0_min : first temperature trigger's min freq +;ths_trip_0_max : first temperature trigger's max freq +;ths_trip_1_min : second temperature trigger's min freq +;ths_trip_1_max : second temperature trigger's max freq +;---------------------------------------------------------------------------------- + [ths_para] ths_used = 1 ths_trip1_count = 8 @@ -284,6 +411,10 @@ ths_trip1_7_max = 0 ths_trip2_count = 1 ths_trip2_0 = 105 +;---------------------------------------------------------------------------------- +;cooler_table cooler_count <=32 +;---------------------------------------------------------------------------------- + [cooler_table] cooler_count = 11 cooler0 = "1200000 4 4294967295 0" @@ -299,444 +430,710 @@ cooler9 = "240000 2 4294967295 0" cooler10 = "240000 1 4294967295 0" [nand0_para] -nand_support_2ch = 0 -nand0_used = 0 -nand0_we = port:PC00<2> -nand0_ale = port:PC01<2> -nand0_cle = port:PC02<2> -nand0_ce1 = port:PC03<2> -nand0_ce0 = port:PC04<2> -nand0_nre = port:PC05<2> -nand0_rb0 = port:PC06<2> -nand0_rb1 = port:PC07<2> -nand0_d0 = port:PC08<2> -nand0_d1 = port:PC09<2> -nand0_d2 = port:PC10<2> -nand0_d3 = port:PC11<2> -nand0_d4 = port:PC12<2> -nand0_d5 = port:PC13<2> -nand0_d6 = port:PC14<2> -nand0_d7 = port:PC15<2> -nand0_ndqs = port:PC16<2> +nand_support_2ch = 0 +nand0_used = 0 +nand0_we = port:PC00<2> +nand0_ale = port:PC01<2> +nand0_cle = port:PC02<2> +nand0_ce1 = port:PC03<2> +nand0_ce0 = port:PC04<2> +nand0_nre = port:PC05<2> +nand0_rb0 = port:PC06<2> +nand0_rb1 = port:PC07<2> +nand0_d0 = port:PC08<2> +nand0_d1 = port:PC09<2> +nand0_d2 = port:PC10<2> +nand0_d3 = port:PC11<2> +nand0_d4 = port:PC12<2> +nand0_d5 = port:PC13<2> +nand0_d6 = port:PC14<2> +nand0_d7 = port:PC15<2> +nand0_ndqs = port:PC16<2> + + +;----------------------------------------------------------------- +;auto_hpd - 1:need hotplud for hdmi/tv; 0:don't hotplud for lcd +;output_type - 0:none; 1:lcd; 2:tv; 4:hdmi; 8:vga (as default config in homlet) +;hdmi_channel- the display channel for hdmi (as default config in homlet) +;cvbs_channel- the display channel for cvbs (as default config in homlet) +;hdmi_mode - as default config for output of hdmi in homlet +;cvbs_mode - as default config for output of tv in homlet. 11:PAL; 14:NTSC +;check the definition(of hdmi/cvbs_mode) of disp_tv_mode in sunxi_display2.h +;hdmi_mode_check - disable/enable the function of checking hdmi mode, 0 is disable, 1 is enable +;----------------------------------------------------------------- [boot_disp] -advert_disp = 0 -auto_hpd = 1 -output_type = 4 -hdmi_channel = 0 -hdmi_mode = 4 -cvbs_channel = 1 -cvbs_mode = 11 -output_full = 1 +advert_disp = 0 +auto_hpd = 1 +output_type = 4 +hdmi_channel = 0 +hdmi_mode = 4 +cvbs_channel = 1 +cvbs_mode = 11 +output_full = 1 hdmi_mode_check = 1 +;---------------------------------------------------------------------------------- +;disp init configuration +; +;disp_mode (0:screen0; 1:screen1) +;screenx_output_type (0:none; 1:lcd; 3:hdmi;) +;screenx_output_mode (used for hdmi output, 0:480i 1:576i 2:480p 3:576p 4:720p50) +; (5:720p60 6:1080i50 7:1080i60 8:1080p24 9:1080p50 10:1080p60) +;fbx format (0:ARGB 1:ABGR 2:RGBA 3:BGRA 5:RGB565 8:RGB888 12:ARGB4444 16:ARGB1555 18:RGBA5551) +;fbx_width,fbx_height (framebuffer horizontal/vertical pixels, fix to output resolution while equal 0) +;lcdx_backlight (lcd init backlight,the range:[0,256],default:197 +;---------------------------------------------------------------------------------- [disp_init] -disp_init_enable = 1 -disp_mode = 0 -screen0_output_type = 3 -screen0_output_mode = 5 -screen1_output_type = 3 -screen1_output_mode = 5 -fb0_format = 0 -fb0_width = 0 -fb0_height = 0 -fb1_format = 0 -fb1_width = 0 -fb1_height = 0 -fb0_framebuffer_num = 3 -sunxi_fb_mem_reserve = 32 +disp_init_enable = 1 +disp_mode = 0 +screen0_output_type = 3 +screen0_output_mode = 5 + +screen1_output_type = 3 +screen1_output_mode = 5 + +fb0_format = 0 +fb0_width = 0 +fb0_height = 0 + +fb1_format = 0 +fb1_width = 0 +fb1_height = 0 + +fb0_framebuffer_num = 3 +sunxi_fb_mem_reserve = 32 + +;---------------------------------------------------------------------------------- +;hdmi configuration +;---------------------------------------------------------------------------------- [hdmi_para] -hdmi_used = 1 -hdmi_power = "vcc-hdmi-18" +hdmi_used = 1 +hdmi_power = "vcc-hdmi-18" +;------------------------------------- +; set to 0 for hdmi->dvi compatibility +;------------------------------------- +;hdcp_enable = 0 +;hdmi_cts_compatibility = 1 [tv_para] -tv_used = 1 -tv_dac_used = 1 -tv_dac_src0 = 0 +tv_used = 1 +tv_dac_used = 1 +tv_dac_src0 = 0 +;---------------------------------------------------------------------------------- +;pwm config +;---------------------------------------------------------------------------------- [pwm0_para] -pwm_used = 0 -pwm_positive = port:PA05<3><0> +pwm_used = 0 +pwm_positive = port:PA05<3><0> +;------------------------------------------------------------------------------; +; 10/100/100Mbps Ethernet MAC Controller Configure ; +;------------------------------------------------------------------------------; +; Options: ; +; gmac_used --- 0: not used, 1: external phy, 2: internal phy ; +; gmac_powerx -- A[:B] A: axp channel, B: voltage value ; +; If set gamc_phy to use internal PHY, do not config port ; +;------------------------------------------------------------------------------; +; MII RMII MII RMII MII RMII ; +; PD00 * PD06 * * PD12 * * ; +; PD01 * PD07 * PD13 * * ; +; PD02 * * PD08 * PD14 * ; +; PD03 * * PD09 * * PD15 * ; +; PD04 * PD10 * * PD16 * * ; +; PD05 * PD11 * * PD17 * * ; +;------------------------------------------------------------------------------; [gmac0] -gmac_used = 1 -gmac_rxd3 = port:PD00<2><3> -gmac_rxd2 = port:PD01<2><3> -gmac_rxd1 = port:PD02<2><3> -gmac_rxd0 = port:PD03<2><3> -gmac_rxclk = port:PD04<2><3> -gmac_rxdv = port:PD05<2><3> -gmac_txd3 = port:PD07<2><3> -gmac_txd2 = port:PD08<2><3> -gmac_txd1 = port:PD09<2><3> -gmac_txd0 = port:PD10<2><3> -gmac_txclk = port:PD12<2><3> -gmac_txen = port:PD13<2><3> -gmac_col = port:PD15<2><3> -gmac_mdc = port:PD16<2><3> -gmac_mdio = port:PD17<2><3> -gmac_power1 = +gmac_used = 1 +gmac_rxd3 = port:PD00<2><3> +gmac_rxd2 = port:PD01<2><3> +gmac_rxd1 = port:PD02<2><3> +gmac_rxd0 = port:PD03<2><3> +gmac_rxclk = port:PD04<2><3> +gmac_rxdv = port:PD05<2><3> +;gmac_rxerr = port:PD06<2><3> +gmac_txd3 = port:PD07<2><3> +gmac_txd2 = port:PD08<2><3> +gmac_txd1 = port:PD09<2><3> +gmac_txd0 = port:PD10<2><3> +;gmac_crs = port:PD11<2><3> +gmac_txclk = port:PD12<2><3> +gmac_txen = port:PD13<2><3> +;gmac_txerr = port:PD14<2><3> +gmac_col = port:PD15<2><3> +gmac_mdc = port:PD16<2><3> +gmac_mdio = port:PD17<2><3> +gmac_power1 = [gmac_phy_power] -gmac_phy_power_en = port:PD06<1><0> +gmac_phy_power_en = port:PD06<1><0> + +;-------------------------------------------------------------------------------- +;vip (video input port) configuration +;vip_used: 0:disable 1:enable +;vip_mode: 0:sample one interface to one buffer 1:sample two interface to one buffer +;vip_dev_qty: The quantity of devices linked to capture bus +; +;vip_define_sensor_list: If you want use sensor detect function, please set vip_define_sensor_list = 1, and +; verify that file /system/etc/hawkview/sensor_list_cfg.ini is properly configured! +; +;vip_dev(x)_pos: sensor position, "rear" or "front", if vip_define_sensor_list = 1, +;vip_dev(x)_pos must be configured! +; +;vip_dev(x)_isp_used 0:not use isp 1:use isp +;vip_dev(x)_fmt: 0:yuv 1:bayer raw rgb +;vip_dev(x)_stby_mode: 0:not shut down power at standby 1:shut down power at standby +;vip_dev(x)_vflip: flip in vertical direction 0:disable 1:enable +;vip_dev(x)_hflip: flip in horizontal direction 0:disable 1:enable +;vip_dev(x)_iovdd: camera module io power handle string, pmu power supply +;vip_dev(x)_iovdd_vol: camera module io power voltage, pmu power supply +;vip_dev(x)_avdd: camera module analog power handle string, pmu power supply +;vip_dev(x)_avdd_vol: camera module analog power voltage, pmu power supply +;vip_dev(x)_dvdd: camera module core power handle string, pmu power supply +;vip_dev(x)_dvdd_vol: camera module core power voltage, pmu power supply +;vip_dev(x)_afvdd: camera module vcm power handle string, pmu power supply +;vip_dev(x)_afvdd_vol: camera module vcm power voltage, pmu power supply +;x indicates the index of the devices which are linked to the same capture bus +;fill voltage in uV, e.g. iovdd = 2.8V, vip_devx_iovdd_vol = 2800000 +;fill handle string as below: +;axp22_eldo3 +;axp22_dldo4 +;axp22_eldo2 +;fill handle string "" when not using any pmu power supply +;-------------------------------------------------------------------------------- [csi0] -vip_used = 1 -vip_mode = 0 -vip_dev_qty = 1 -vip_define_sensor_list = 0 -vip_csi_pck = port:PE00<2> -vip_csi_mck = port:PE01<2> -vip_csi_hsync = port:PE02<2> -vip_csi_vsync = port:PE03<2> -vip_csi_d0 = port:PE04<2> -vip_csi_d1 = port:PE05<2> -vip_csi_d2 = port:PE06<2> -vip_csi_d3 = port:PE07<2> -vip_csi_d4 = port:PE08<2> -vip_csi_d5 = port:PE09<2> -vip_csi_d6 = port:PE10<2> -vip_csi_d7 = port:PE11<2> -vip_csi_sck = port:PE12<2> -vip_csi_sda = port:PE13<2> -vip_dev0_mname = "ov5640" -vip_dev0_pos = "rear" -vip_dev0_lane = 4 -vip_dev0_twi_id = 2 -vip_dev0_twi_addr = 120 -vip_dev0_isp_used = 1 -vip_dev0_fmt = 1 -vip_dev0_stby_mode = 1 -vip_dev0_vflip = 0 -vip_dev0_hflip = 0 -vip_dev0_iovdd = "" -vip_dev0_iovdd_vol = 2800000 -vip_dev0_avdd = "" -vip_dev0_avdd_vol = 2800000 -vip_dev0_dvdd = "" -vip_dev0_dvdd_vol = 1500000 -vip_dev0_afvdd = "" -vip_dev0_afvdd_vol = 2800000 -vip_dev0_power_en = port:PD14<1> -vip_dev0_reset = port:PE14<1> -vip_dev0_pwdn = port:PE15<1> -vip_dev0_flash_en = -vip_dev0_flash_mode = -vip_dev0_af_pwdn = -vip_dev0_act_used = 0 -vip_dev0_act_name = "ad5820_act" -vip_dev0_act_slave = 24 -vip_dev1_mname = "" -vip_dev1_pos = "front" -vip_dev1_lane = 1 -vip_dev1_twi_id = 0 -vip_dev1_twi_addr = -vip_dev1_isp_used = 0 -vip_dev1_fmt = 1 -vip_dev1_stby_mode = 0 -vip_dev1_vflip = 0 -vip_dev1_hflip = 0 -vip_dev1_iovdd = "" -vip_dev1_iovdd_vol = 2800000 -vip_dev1_avdd = "" -vip_dev1_avdd_vol = 2800000 -vip_dev1_dvdd = "" -vip_dev1_dvdd_vol = 1500000 -vip_dev1_afvdd = "" -vip_dev1_afvdd_vol = 2800000 -vip_dev1_power_en = -vip_dev1_reset = -vip_dev1_pwdn = -vip_dev1_flash_en = -vip_dev1_flash_mode = -vip_dev1_af_pwdn = +vip_used = 1 +vip_mode = 0 +vip_dev_qty = 1 +vip_define_sensor_list = 0 + +vip_csi_pck = port:PE00<2> +vip_csi_mck = port:PE01<2> +vip_csi_hsync = port:PE02<2> +vip_csi_vsync = port:PE03<2> +vip_csi_d0 = port:PE04<2> +vip_csi_d1 = port:PE05<2> +vip_csi_d2 = port:PE06<2> +vip_csi_d3 = port:PE07<2> +vip_csi_d4 = port:PE08<2> +vip_csi_d5 = port:PE09<2> +vip_csi_d6 = port:PE10<2> +vip_csi_d7 = port:PE11<2> +vip_csi_sck = port:PE12<2> +vip_csi_sda = port:PE13<2> + +vip_dev0_mname = "ov5640" +vip_dev0_pos = "rear" +vip_dev0_lane = 4 +vip_dev0_twi_id = 2 +vip_dev0_twi_addr = 0x78 +vip_dev0_isp_used = 1 +vip_dev0_fmt = 1 +vip_dev0_stby_mode = 1 +vip_dev0_vflip = 0 +vip_dev0_hflip = 0 +vip_dev0_iovdd = "" +vip_dev0_iovdd_vol = 2800000 +vip_dev0_avdd = "" +vip_dev0_avdd_vol = 2800000 +vip_dev0_dvdd = "" +vip_dev0_dvdd_vol = 1500000 +vip_dev0_afvdd = "" +vip_dev0_afvdd_vol = 2800000 +vip_dev0_power_en = port:PD14<1> +vip_dev0_reset = port:PE14<1> +vip_dev0_pwdn = port:PE15<1> +vip_dev0_flash_en = +vip_dev0_flash_mode = +vip_dev0_af_pwdn = + +vip_dev0_act_used = 0 +vip_dev0_act_name = "ad5820_act" +vip_dev0_act_slave = 0x18 + + +vip_dev1_mname = "" +vip_dev1_pos = "front" +vip_dev1_lane = 1 +vip_dev1_twi_id = 0 +vip_dev1_twi_addr = +vip_dev1_isp_used = 0 +vip_dev1_fmt = 1 +vip_dev1_stby_mode = 0 +vip_dev1_vflip = 0 +vip_dev1_hflip = 0 +vip_dev1_iovdd = "" +vip_dev1_iovdd_vol = 2800000 +vip_dev1_avdd = "" +vip_dev1_avdd_vol = 2800000 +vip_dev1_dvdd = "" +vip_dev1_dvdd_vol = 1500000 +vip_dev1_afvdd = "" +vip_dev1_afvdd_vol = 2800000 +vip_dev1_power_en = +vip_dev1_reset = +vip_dev1_pwdn = +vip_dev1_flash_en = +vip_dev1_flash_mode = +vip_dev1_af_pwdn = + + +;-------------------------------------------------------------------------------- +;tv configuration +; +;-------------------------------------------------------------------------------- [tvout_para] -tvout_used = -tvout_channel_num = -tv_en = +tvout_used = +tvout_channel_num = +tv_en = [tvin_para] -tvin_used = -tvin_channel_num = +tvin_used = +tvin_channel_num = +;---------------------------------------------------------------------------------- +;DE-Interlace configuration +;---------------------------------------------------------------------------------- [di_para] -di_used = 1 +di_used = 1 +;-------------------------------------------------------------------------------- +; SDMMC PINS MAPPING | +; ------------------------------------------------------------------------------| +; Config Guide | +; sdc_used: 1-enable card, 0-disable card | +; sdc_detmode: card detect mode | +; 1-detect card by gpio polling | +; 2-detect card by gpio irq(must use IO with irq function) | +; 3-no detect, always in for boot card | +; 4-manually insert and remove by /proc/driver/sunxi-mmc.x/insert| +; sdc_buswidth: card bus width, 1-1bit, 4-4bit, 8-8bit | +; sdc_use_wp: 1-with write protect IO, 0-no write protect IO | +; sdc_isio: for sdio card | +; sdc_regulator: power control.if card supports UHS-I/DDR and HS200 timing for| +; SD3.0 or eMMC4.5, regulator must be configured. the value is | +; the ldo name of AXP221, eg: sdc_regulator = "axp22_eldo2" | +; other: GPIO Mapping configuration | +; ------------------------------------------------------------------------------| +; Note: | +; 1 if detmode=2, sdc_det's config=6 | +; else if detmode=1, sdc_det's config=0 | +; else sdc_det IO is not necessary | +; 2 if the customer wants to support UHS-I and HS200 features, he must provide| +; an independent power supply for the card. This is only used in platforms | +; that supports SD3.0 cards and eMMC4.4+ flashes | +;-------------------------------------------------------------------------------- [mmc0_para] -sdc_used = 1 -sdc_detmode = 3 -sdc_buswidth = 4 -sdc_clk = port:PF02<2><1><2> -sdc_cmd = port:PF03<2><1><2> -sdc_d0 = port:PF01<2><1><2> -sdc_d1 = port:PF00<2><1><2> -sdc_d2 = port:PF05<2><1><2> -sdc_d3 = port:PF04<2><1><2> -sdc_det = port:PF06<0><1><2> -sdc_use_wp = 0 -sdc_wp = -sdc_isio = 0 -sdc_regulator = "none" -sdc_power_supply = "none" +sdc_used = 1 +sdc_detmode = 3 +sdc_buswidth = 4 +sdc_clk = port:PF02<2><1><2> +sdc_cmd = port:PF03<2><1><2> +sdc_d0 = port:PF01<2><1><2> +sdc_d1 = port:PF00<2><1><2> +sdc_d2 = port:PF05<2><1><2> +sdc_d3 = port:PF04<2><1><2> +sdc_det = port:PF06<0><1><2> +sdc_use_wp = 0 +sdc_wp = +sdc_isio = 0 +sdc_regulator = "none" +sdc_power_supply = "none" [mmc1_para] -sdc_used = 1 -sdc_detmode = 4 -sdc_buswidth = 4 -sdc_clk = port:PG00<2><1><3> -sdc_cmd = port:PG01<2><1><3> -sdc_d0 = port:PG02<2><1><3> -sdc_d1 = port:PG03<2><1><3> -sdc_d2 = port:PG04<2><1><3> -sdc_d3 = port:PG05<2><1><3> -sdc_det = -sdc_use_wp = 0 -sdc_wp = -sdc_isio = 1 -sdc_regulator = "none" -sdc_power_supply = "none" -sdc_2xmode = 1 -sdc_ddrmode = 1 +sdc_used = 1 +sdc_detmode = 4 +sdc_buswidth = 4 +sdc_clk = port:PG00<2><1><3> +sdc_cmd = port:PG01<2><1><3> +sdc_d0 = port:PG02<2><1><3> +sdc_d1 = port:PG03<2><1><3> +sdc_d2 = port:PG04<2><1><3> +sdc_d3 = port:PG05<2><1><3> +sdc_det = +sdc_use_wp = 0 +sdc_wp = +sdc_isio = 1 +sdc_regulator = "none" +sdc_power_supply = "none" +sdc_2xmode = 1 +sdc_ddrmode = 1 [mmc2_para] -sdc_used = 1 -sdc_detmode = 1 -sdc_buswidth = 8 -sdc_clk = port:PC05<3><1><2> -sdc_cmd = port:PC06<3><1><2> -sdc_d0 = port:PC08<3><1><2> -sdc_d1 = port:PC09<3><1><2> -sdc_d2 = port:PC10<3><1><2> -sdc_d3 = port:PC11<3><1><2> -sdc_d4 = port:PC12<3><1><2> -sdc_d5 = port:PC13<3><1><2> -sdc_d6 = port:PC14<3><1><2> -sdc_d7 = port:PC15<3><1><2> -emmc_rst = port:PC16<3><1><2> -sdc_det = -sdc_use_wp = 0 -sdc_wp = -sdc_isio = 0 -sdc_regulator = "none" -sdc_power_supply = "none" -sdc_2xmode = 1 -sdc_ddrmode = 1 +sdc_used = 1 +sdc_detmode = 1 +sdc_buswidth = 8 +sdc_clk = port:PC05<3><1><2> +sdc_cmd = port:PC06<3><1><2> +sdc_d0 = port:PC08<3><1><2> +sdc_d1 = port:PC09<3><1><2> +sdc_d2 = port:PC10<3><1><2> +sdc_d3 = port:PC11<3><1><2> +sdc_d4 = port:PC12<3><1><2> +sdc_d5 = port:PC13<3><1><2> +sdc_d6 = port:PC14<3><1><2> +sdc_d7 = port:PC15<3><1><2> +emmc_rst = port:PC16<3><1><2> +sdc_det = +sdc_use_wp = 0 +sdc_wp = +sdc_isio = 0 +sdc_regulator = "none" +sdc_power_supply = "none" +sdc_2xmode = 1 +sdc_ddrmode = 1 +; ------------------------------------------------------------------------------| +; sim card configuration +;-------------------------------------------------------------------------------- [smc_para] -smc_used = 0 -smc_rst = port:PA09<2> -smc_vppen = port:PA20<3> -smc_vppp = port:PA21<3> -smc_det = port:PA10<2> -smc_vccen = port:PA06<2> -smc_sck = port:PA07<2> -smc_sda = port:PA08<2> +smc_used = 0 +smc_rst = port:PA09<2> +smc_vppen = port:PA20<3> +smc_vppp = port:PA21<3> +smc_det = port:PA10<2> +smc_vccen = port:PA06<2> +smc_sck = port:PA07<2> +smc_sda = port:PA08<2> + +;-------------------------------- +; [usbc0]: Controller 0 configuration. +; usb used: USB enable flag. Set, indicating that the system USB module is available, is set to 0, it means that the system USB is disabled. +; usb_port_type: USB port usage. 0: device only; 1: host only; 2: OTG +; usb_detect_type: USB port of checking. 0: not detected; 1: vbus / id checks; 2: id / dpdm check +; usb_id_gpio: USB ID pin pin configuration. For details, please refer gpio configuration instructions. +; usb_det_vbus_gpio: USB DET_VBUS pin pin configuration. For details, please refer gpio configuration instructions. +; usb_drv_vbus_gpio: USB DRY_VBUS pin pin configuration. For details, please refer gpio configuration instructions. +; usb_det_vbus_gpio: "axp_ctrl", represents axp offer +; usb_restrict_gpio: usb limiting control pin +; usb_restric_flag: usb limiting standard set +;-------------------------------- +;-------------------------------- +;--- USB0控制标志 +;-------------------------------- [usbc0] -usb_used = 1 -usb_port_type = 1 -usb_detect_type = 0 -usb_id_gpio = port:PL06<0><1> -usb_det_vbus_gpio = "axp_ctrl" -usb_drv_vbus_gpio = port:PD11<1><0><0> +usb_used = 1 +usb_port_type = 1 +usb_detect_type = 0 +usb_id_gpio = port:PL06<0><1> +usb_det_vbus_gpio = "axp_ctrl" +usb_drv_vbus_gpio = port:PD11<1><0><0> usb_host_init_state = 1 -usb_restrict_gpio = -usb_restric_flag = 0 +usb_restrict_gpio = +usb_restric_flag = 0 usb_restric_voltage = 3550000 -usb_restric_capacity = 5 -usb_regulator_io = "nocare" -usb_regulator_vol = 0 -usb_not_suspend = 0 +usb_restric_capacity= 5 +usb_regulator_io = "nocare" +usb_regulator_vol = 0 +usb_not_suspend = 0 +;-------------------------------- +;--- USB1控制标志 +;-------------------------------- [usbc1] -usb_used = 1 -usb_drv_vbus_gpio = -usb_restrict_gpio = +usb_used = 1 +usb_drv_vbus_gpio = +usb_restrict_gpio = usb_host_init_state = 1 -usb_restric_flag = 0 -usb_regulator_io = "nocare" -usb_regulator_vol = 0 -usb_not_suspend = 0 +usb_restric_flag = 0 +usb_regulator_io = "nocare" +usb_regulator_vol = 0 +usb_not_suspend = 0 +;-------------------------------- +;--- USB2控制标志 +;-------------------------------- [usbc2] -usb_used = 1 -usb_drv_vbus_gpio = -usb_restrict_gpio = +usb_used = 1 +usb_drv_vbus_gpio = +usb_restrict_gpio = usb_host_init_state = 1 -usb_restric_flag = 0 -usb_regulator_io = "nocare" -usb_regulator_vol = 0 -usb_not_suspend = 0 +usb_restric_flag = 0 +usb_regulator_io = "nocare" +usb_regulator_vol = 0 +usb_not_suspend = 0 +;-------------------------------- +;--- USB3控制标志 +;-------------------------------- [usbc3] -usb_used = 0 -usb_drv_vbus_gpio = -usb_restrict_gpio = +usb_used = 0 +usb_drv_vbus_gpio = +usb_restrict_gpio = usb_host_init_state = 1 -usb_restric_flag = 0 -usb_regulator_io = "nocare" -usb_regulator_vol = 0 -usb_not_suspend = 0 +usb_restric_flag = 0 +usb_regulator_io = "nocare" +usb_regulator_vol = 0 +usb_not_suspend = 0 +;-------------------------------- +;--- USB Device +;-------------------------------- [usb_feature] -vendor_id = 6353 -mass_storage_id = 1 -adb_id = 2 -manufacturer_name = "USB Developer" -product_name = "Android" -serial_number = "20080411" +vendor_id = 0x18D1 +mass_storage_id = 0x0001 +adb_id = 0x0002 + +manufacturer_name = "USB Developer" +product_name = "Android" +serial_number = "20080411" [msc_feature] -vendor_name = "USB 2.0" -product_name = "USB Flash Driver" -release = 100 -luns = 3 +vendor_name = "USB 2.0" +product_name = "USB Flash Driver" +release = 100 +luns = 3 [serial_feature] -serial_unique = 0 +serial_unique = 0 + +;-------------------------------------------------------------------------------- +;wifi/bt/fm/gps/nfc modules configuration +;module_num: +; 0- none +; 1- rtl8188eu(wifi) +; 2- rtl8723bs(wifi+bt) +; 3- ap6181(wifi) +; 4- ap6210(wifi+bt) +; 5- ap6330(wifi+bt) +; 6- ap6335(wifi) +; 7- rtl8189etv(wifi) +;module_power0: axp used by module, "axp22_dldo1" - use dldo1, not use keep it empty +;module_power0_vol: power0 voltage, mv; +;chip_en: enable chip io +;lpo_use_apclk: ""- not use, "losc_out"- a23/33/H3, "ac10032k1"、"ac10032k2"、"ac10032k3"- a80 +;-------------------------------------------------------------------------------- [module_para] -module_num = 4 -module_power0 = -module_power0_vol = 0 -module_power1 = -module_power1_vol = 1 -module_power2 = -module_power2_vol = -module_power3 = -module_power3_vol = -chip_en = -lpo_use_apclk = "losc_out" +module_num = 4 +module_power0 = +module_power0_vol = 0 +module_power1 = +module_power1_vol = 1 +module_power2 = +module_power2_vol = +module_power3 = +module_power3_vol = +chip_en = +lpo_use_apclk = "losc_out" +;-------------------------------------------------------------------------------- +;wifi configuration +;wifi_sdc_id: 0- SDC0, 1- SDC1, 2- SDC2, 3- SDC3 +;wifi_usbc_id: 0- USB0, 1- USB1, 2- USB2 +;wifi_usbc_type: 1- EHCI(speed 2.0), 2- OHCI(speed 1.0) +;wl_reg_on: wifi function enable pin +;wl_host_wake: wlan device wake-up host pin +;wl_host_wake_invert: whether wl_host_wake use inverter between ap and module +; 0: not used, 1: used +;-------------------------------------------------------------------------------- [wifi_para] -wifi_used = 1 -wifi_sdc_id = 1 -wifi_usbc_id = 1 -wifi_usbc_type = 1 -wl_reg_on = port:PL07<1><0> -wl_host_wake = port:PG10<0><0> -wl_host_wake_invert = 0 +wifi_used = 1 +wifi_sdc_id = 1 +wifi_usbc_id = 1 +wifi_usbc_type = 1 +wl_reg_on = port:PL07<1><0> +wl_host_wake = port:PG10<0><0> +wl_host_wake_invert = 0 +;-------------------------------------------------------------------------------- +;bluetooth configuration +;bt_used: 0- no used, 1- used +;bt_uard_id: 0- uart0, 1- uart1, 2- uart2 +;bt_uart_baud: uart baud rate, unit: bps +;bt_rst_n: bt function enable io +;bt_wake: host wake-up bluetooth device +;bt_host_wake: bt device wake-up host +;bt_host_wake_invert: whether bt_host_wake use inverter between ap and module +; 0: not used, 1: used +;-------------------------------------------------------------------------------- [bt_para] -bt_used = 1 -bt_uart_id = 1 -bt_uart_baud = 1500000 -bt_rst_n = port:PG12<1><0> -bt_wake = port:PG13<1><0> -bt_host_wake = port:PG11<0><0> -bt_host_wake_invert = 0 +bt_used = 1 +bt_uart_id = 1 +bt_uart_baud = 1500000 +bt_rst_n = port:PG12<1><0> +bt_wake = port:PG13<1><0> +bt_host_wake = port:PG11<0><0> +bt_host_wake_invert = 0 +;-------------------------------------------------------------------------------- +;daudio_master:1: SND_SOC_DAIFMT_CBM_CFM(codec clk & FRM master) use +; 2: SND_SOC_DAIFMT_CBS_CFM(codec clk slave & FRM master) not use +; 3: SND_SOC_DAIFMT_CBM_CFS(codec clk master & frame slave) not use +; 4: SND_SOC_DAIFMT_CBS_CFS(codec clk & FRM slave) use +;daudio_select:0 is pcm.1 is i2s +;audio_format: 1:SND_SOC_DAIFMT_I2S(standard i2s format). use +; 2:SND_SOC_DAIFMT_RIGHT_J(right justfied format). +; 3:SND_SOC_DAIFMT_LEFT_J(left justfied format) +; 4:SND_SOC_DAIFMT_DSP_A(pcm. MSB is available on 2nd BCLK rising edge after LRC rising edge). use +; 5:SND_SOC_DAIFMT_DSP_B(pcm. MSB is available on 1nd BCLK rising edge after LRC rising edge) +;signal_inversion:1:SND_SOC_DAIFMT_NB_NF(normal bit clock + frame) use +; 2:SND_SOC_DAIFMT_NB_IF(normal BCLK + inv FRM) +; 3:SND_SOC_DAIFMT_IB_NF(invert BCLK + nor FRM) use +; 4:SND_SOC_DAIFMT_IB_IF(invert BCLK + FRM) +;over_sample_rate: support 128fs/192fs/256fs/384fs/512fs/768fs +;sample_resolution :16bits/20bits/24bits +;word_select_size :16bits/20bits/24bits/32bits +;pcm_sync_period :16/32/64/128/256 +;msb_lsb_first :0: msb first; 1: lsb first +;sign_extend :0: zero pending; 1: sign extend +;slot_index :slot index: 0: the 1st slot - 3: the 4th slot +;slot_width :8 bit width / 16 bit width +;frame_width :0: long frame = 2 clock width; 1: short frame +;tx_data_mode :0: 16bit linear PCM; 1: 8bit linear PCM; 2: 8bit u-law; 3: 8bit a-law +;rx_data_mode :0: 16bit linear PCM; 1: 8bit linear PCM; 2: 8bit u-law; 3: 8bit a-law +;-------------------------------------------------------------------------------- [pcm0] -daudio_used = 0 -daudio_master = 4 -daudio_select = 1 -audio_format = 1 -signal_inversion = 1 -mclk_fs = 128 -sample_resolution = 16 -slot_width_select = 32 -pcm_lrck_period = 32 -pcm_lrckr_period = 1 -msb_lsb_first = 0 -sign_extend = 0 -slot_index = 0 -slot_width = 32 -frame_width = 0 -tx_data_mode = 0 -rx_data_mode = 0 -i2s_mclk = port:PA18<2><1> -i2s_bclk = port:PA19<2><1> -i2s_dout0 = port:PA20<2><1> -i2s_din = port:PA21<2><1> +daudio_used = 0 +daudio_master = 4 +daudio_select = 1 +audio_format = 1 +signal_inversion = 1 +mclk_fs = 128 +sample_resolution = 16 +slot_width_select = 32 +;pcm_sync_period = 256 +pcm_lrck_period = 32 +pcm_lrckr_period = 1 +msb_lsb_first = 0 +sign_extend = 0 +slot_index = 0 +slot_width = 32 +frame_width = 0 +tx_data_mode = 0 +rx_data_mode = 0 +i2s_mclk = port:PA18<2><1> +i2s_bclk = port:PA19<2><1> +i2s_dout0 = port:PA20<2><1> +i2s_din = port:PA21<2><1> + [pcm1] -daudio_used = 0 -daudio_master = 4 -daudio_select = 1 -audio_format = 1 -signal_inversion = 1 -mclk_fs = 128 -sample_resolution = 16 -slot_width_select = 32 -pcm_lrck_period = 32 -pcm_lrckr_period = 1 -msb_lsb_first = 0 -sign_extend = 0 -slot_index = 0 -slot_width = 32 -frame_width = 0 -tx_data_mode = 0 -rx_data_mode = 0 -i2s_mclk = port:PG10<2><1> -i2s_bclk = port:PG11<2><1> -i2s_dout0 = port:PG12<2><1> -i2s_din = port:PG13<2><1> +daudio_used = 0 +daudio_master = 4 +daudio_select = 1 +audio_format = 1 +signal_inversion = 1 +mclk_fs = 128 +sample_resolution = 16 +slot_width_select = 32 +;pcm_sync_period = 256 +pcm_lrck_period = 32 +pcm_lrckr_period = 1 +msb_lsb_first = 0 +sign_extend = 0 +slot_index = 0 +slot_width = 32 +frame_width = 0 +tx_data_mode = 0 +rx_data_mode = 0 +i2s_mclk = port:PG10<2><1> +i2s_bclk = port:PG11<2><1> +i2s_dout0 = port:PG12<2><1> +i2s_din = port:PG13<2><1> + [audio0] -audio_used = 1 -lineout_vol = 31 -cap_vol = 5 -audio_hp_ldo = "none" -adcagc_used = 0 -adcdrc_used = 0 -dacdrc_used = 0 -adchpf_used = 0 -dachpf_used = 0 -audio_pa_ctrl = port:PA16<1><0> +audio_used = 1 +lineout_vol = 0x1f +cap_vol = 0x5 +audio_hp_ldo = "none" +adcagc_used = 0 +adcdrc_used = 0 +dacdrc_used = 0 +adchpf_used = 0 +dachpf_used = 0 +audio_pa_ctrl = port:PA16<1><0> [spdif0] -spdif_used = 0 -spdif_dout = port:PA17<2><1> +spdif_used = 0 +spdif_dout = port:PA17<2><1> [audiohub] -hub_used = 0 -codec_used = 1 -spdif_used = 1 -hdmi_used = 1 +hub_used = 0 +codec_used = 1 +spdif_used = 1 +hdmi_used = 1 +;---------------------------------------------------------------------------------- +;ir rx --- infra remote configuration +;---------------------------------------------------------------------------------- [s_cir0] -ir_used = 1 -ir_rx = port:PL11<2><1> -ir_power_key_code0 = 87 -ir_addr_code0 = 40704 -ir_power_key_code1 = 26 -ir_addr_code1 = 64260 -ir_power_key_code2 = 20 -ir_addr_code2 = 32640 -ir_power_key_code3 = 21 -ir_addr_code3 = 32640 -ir_power_key_code4 = 11 -ir_addr_code4 = 63240 -ir_power_key_code5 = 3 -ir_addr_code5 = 239 -ir_power_key_code6 = 159 -ir_addr_code6 = 19635 -ir_power_key_code7 = 10 -ir_addr_code7 = 30536 -ir_power_key_code8 = 69 -ir_addr_code8 = 48386 -ir_power_key_code9 = 77 -ir_addr_code9 = 56865 -ir_power_key_code10 = 24 -ir_addr_code10 = 65025 -ir_power_key_code11 = 87 -ir_addr_code11 = 65280 -ir_power_key_code12 = 77 -ir_addr_code12 = 65344 -ir_power_key_code13 = 136 -ir_addr_code13 = 56610 +ir_used = 1 +ir_rx = port:PL11<2><1> +ir_power_key_code0 = 0x57 +ir_addr_code0 = 0x9f00 +ir_power_key_code1 = 0x1a +ir_addr_code1 = 0xfb04 +ir_power_key_code2 = 0x14 +ir_addr_code2 = 0x7F80 +ir_power_key_code3 = 0x15 +ir_addr_code3 = 0x7F80 +ir_power_key_code4 = 0x0b +ir_addr_code4 = 0xF708 +ir_power_key_code5 = 0x03 +ir_addr_code5 = 0x00EF +ir_power_key_code6 = 0x9f +ir_addr_code6 = 0x4CB3 +ir_power_key_code7 = 0x0a +ir_addr_code7 = 0x7748 +ir_power_key_code8 = 0x45 +ir_addr_code8 = 0xbd02 +ir_power_key_code9 = 0x4d +ir_addr_code9 = 0xde21 +ir_power_key_code10 = 0x18 +ir_addr_code10 = 0xfe01 +ir_power_key_code11 = 0x57 +ir_addr_code11 = 0xff00 +ir_power_key_code12 = 0x4d +ir_addr_code12 = 0xff40 +ir_power_key_code13 = 0x88 +ir_addr_code13 = 0xdd22 + +;---------------------------------------------------------------------------------- +;ir tx--- infra remote configuration +;---------------------------------------------------------------------------------- [cir] -ir_used = 1 -ir_tx = port:PH07<2> +ir_used = 1 +ir_tx = port:PH07<2> + +;---------------------------------------------------------------------------------- +; dvfs voltage-frequency table configuration +; +; pmuic_type:0:none, 1:gpio, 2:i2c +; pmu_gpio0: gpio config. +; pmu_levelx: 0~9999: voltage(mV), 10000~90000:gpio0 state. voltage form high to low. +; +; extremity_freq(Hz): cpu extremity frequency when run benckmark or demo apk +; 1536MHz@1500mV with radiator, 1296MHz@1340mV without radiator +; max_freq: cpu maximum frequency, based on Hz, can not be more than 1200MHz +; min_freq: cpu minimum frequency, based on Hz, can not be less than 60MHz +; +; LV_count: count of LV_freq/LV_volt, must be < 16 +; +; LV1: core vdd is 1.50v if cpu frequency is (1296Mhz, 1536Mhz] +; LV2: core vdd is 1.34v if cpu frequency is (1200Mhz, 1296Mhz] +; LV3: core vdd is 1.32v if cpu frequency is (1008Mhz, 1200Mhz] +; LV4: core vdd is 1.20v if cpu frequency is (816Mhz, 1008Mhz] +; LV5: core vdd is 1.10v if cpu frequency is (648Mhz, 816Mhz] +; LV6: core vdd is 1.04v if cpu frequency is (0Mhz, 648Mhz] +; LV7: core vdd is 1.04v if cpu frequency is (0Mhz, 648Mhz] +; LV8: core vdd is 1.04v if cpu frequency is (0Mhz, 648Mhz] +; +;---------------------------------------------------------------------------------- [dvfs_table] pmuic_type = 0 -pmu_gpio0 = port:PL06<1><1><2><1> +pmu_gpio0 = port:PL06<1><1><2><1> pmu_level0 = 11300 pmu_level1 = 1100 +;extremity_freq = 1296000000 max_freq = 1200000000 min_freq = 648000000 LV_count = 2 @@ -746,99 +1143,167 @@ LV2_freq = 648000000 LV2_volt = 1300 [gpu_dvfs_table] + G_LV_count = 3 + G_LV0_freq = 312000000 G_LV0_volt = 1200000 + G_LV1_freq = 384000000 G_LV1_volt = 1200000 + G_LV2_freq = 456000000 G_LV2_volt = 1200000 +;---------------------------------------------------------------------------------- +;special gpio config for Board Vendor ID +;vid_used -- if board need distinguished by gpio,set '1';if not,set '0' +;vid_count -- the count of vendor id bits +;vid_bit_[0..3] -- gpio config for each bit of board vendor id +;example: vendor id hex format :{0x 0 0 1 0 } +; | | | | +; [vid_bit_3] [vid_bit_2] [vid_bit_1] [vid_bit_0] +;---------------------------------------------------------------------------------- [board_vendor] -vid_used = 0 -vid_count = 0 -vid_bit_0 = port:PD16<0><1> -vid_bit_1 = port:PD15<0><1> -vid_bit_2 = port:PD14<0><1> -vid_bit_3 = port:PD13<0><1> -vid_bit_4 = port:PD12<0><1> -vid_bit_5 = port:PD17<0><1> +vid_used = 0 +vid_count = 0 +vid_bit_0 = port:PD16<0><1> +vid_bit_1 = port:PD15<0><1> +vid_bit_2 = port:PD14<0><1> +vid_bit_3 = port:PD13<0><1> +vid_bit_4 = port:PD12<0><1> +vid_bit_5 = port:PD17<0><1> +;---------------------------------------------------------------------------------- +;virtual device +;virtual device for pinctrl testing +;device have pin PA1 PA2 +;---------------------------------------------------------------------------------- [Vdevice] -Vdevice_used = 0 -Vdevice_0 = port:PH10<5><1><2> -Vdevice_1 = port:PH11<5><1><2> +Vdevice_used = 0 +Vdevice_0 = port:PH10<5><1><2> +Vdevice_1 = port:PH11<5><1><2> +;---------------------------------------------------------------------------------- +;s_uart0 config parameters +;s_uart_used --s_uart0 whether used for arisc debugging +;---------------------------------------------------------------------------------- [s_uart0] -s_uart_used = 0 -s_uart_tx = port:PL02<2> -s_uart_rx = port:PL03<2> +s_uart_used = 0 +s_uart_tx = port:PL02<2> +s_uart_rx = port:PL03<2> +;---------------------------------------------------------------------------------- +;s_rsb0 config parameters +;s_rsb_used --s_rsb0 whether used for arisc +;---------------------------------------------------------------------------------- [s_rsb0] -s_rsb_used = 1 -s_rsb_sck = port:PL00<2><1><2> -s_rsb_sda = port:PL01<2><1><2> +s_rsb_used = 1 +s_rsb_sck = port:PL00<2><1><2> +s_rsb_sda = port:PL01<2><1><2> +;---------------------------------------------------------------------------------- +;s_jtag0 config parameters +;s_jtag0_used --s_jtag0 whether used for arisc +; +;---------------------------------------------------------------------------------- [s_jtag0] -s_jtag_used = 0 -s_jtag_tms = port:PL04<2><1><2> -s_jtag_tck = port:PL05<2><1><2> -s_jtag_tdo = port:PL06<2><1><2> -s_jtag_tdi = port:PL07<2><1><2> +s_jtag_used = 0 +s_jtag_tms = port:PL04<2><1><2> +s_jtag_tck = port:PL05<2><1><2> +s_jtag_tdo = port:PL06<2><1><2> +s_jtag_tdi = port:PL07<2><1><2> +;---------------------------------------------------------------------------------- +;s_powchk cpus power check +;s_powchk_used --power check whether used for arisc in super standby +; bit31:enable power updat, bit1:wakeup when power state exception +; bit0:wakeup when power consumption exception +;s_power_reg the expected regs stand for power on/off state +;s_system_power the limit maxmum power consumption when super standby (unit: mw) +; +;---------------------------------------------------------------------------------- [s_powchk] -s_powchk_used = -2147483648 -s_power_reg = 0 -s_system_power = 50 +s_powchk_used = 0x80000000 +s_power_reg = 0x00000000 +s_system_power = 50 +;---------------------------------------------------------------------------------- +;scr configuration +;---------------------------------------------------------------------------------- [sim0] -scr_used = 0 -scr_vccen = port:PA06<2> -scr_slk = port:PA07<2> -scr_sda = port:PA08<2> -scr_rst = port:PA09<2> -scr_det = port:PA10<2> +scr_used = 0 +scr_vccen = port:PA06<2> +scr_slk = port:PA07<2> +scr_sda = port:PA08<2> +scr_rst = port:PA09<2> +scr_det = port:PA10<2> + +;-------------------------------------------------------------------------------- +;tsc configuration +;-------------------------------------------------------------------------------- [ts0] -tsc_used = 0 -tsc_clk = port:PE00<3> -tsc_err = port:PE01<3> -tsc_sync = port:PE02<3> -tsc_dvld = port:PE03<3> -tsc_d0 = port:PE04<3> -tsc_d1 = port:PE05<3> -tsc_d2 = port:PE06<3> -tsc_d3 = port:PE07<3> -tsc_d4 = port:PE08<3> -tsc_d5 = port:PE09<3> -tsc_d6 = port:PE10<3> -tsc_d7 = port:PE11<3> +tsc_used = 0 +tsc_clk = port:PE00<3> +tsc_err = port:PE01<3> +tsc_sync = port:PE02<3> +tsc_dvld = port:PE03<3> +tsc_d0 = port:PE04<3> +tsc_d1 = port:PE05<3> +tsc_d2 = port:PE06<3> +tsc_d3 = port:PE07<3> +tsc_d4 = port:PE08<3> +tsc_d5 = port:PE09<3> +tsc_d6 = port:PE10<3> +tsc_d7 = port:PE11<3> +;-------------------------------------------------------------------------------- +;gpio key +;-------------------------------------------------------------------------------- [gpio_power_key] -key_used = 1 -key_io = port:PL03<6><0> +key_used = 1 +key_io = port:PL03<6><0> +;---------------------------------------------------------------------------------- +; key para +; +; key_used --0:not used, 1:used +; key_cnt --how many key button attach to keyadc. +; key*_vol --the threshold of input voltage of key. +; +; For example: if key2_vol < $(keyadc value) < key3_vol, then key3 be reported. +;---------------------------------------------------------------------------------- [key_para] -key_used = 0 -key_cnt = 5 -key1_vol = 222 -key2_vol = 444 -key3_vol = 666 -key4_vol = 857 -key5_vol = 2000 +key_used = 0 +key_cnt = 5 +key1_vol = 222 +key2_vol = 444 +key3_vol = 666 +key4_vol = 857 +key5_vol = 2000 +;---------------------------------------------------------------------------------- +;display seven segment para +;---------------------------------------------------------------------------------- [d7s_para] -d7s_used = 0 -din_gpio = port:PD00<1><1> -clk_gpio = port:PD01<1><1> -stb_gpio = port:PD02<1><1> +d7s_used = 0 +din_gpio = port:PD00<1><1> +clk_gpio = port:PD01<1><1> +stb_gpio = port:PD02<1><1> +;---------------------------------------------------------------------------------- +;mali parameters +;---------------------------------------------------------------------------------- [mali_para] mali_used = 1 mali_clkdiv = 1 mali_extreme_freq = 600 mali_extreme_vol = 1400 +;---------------------------------------------------------------------------------- +;1wire parameters (default - PA20) +;---------------------------------------------------------------------------------- [w1_para] w1_used = 1 gpio = 20