diff --git a/config/orangepione.fex b/config/orangepione.fex
index 1e436a0e72..a8bfa1a42e 100644
--- a/config/orangepione.fex
+++ b/config/orangepione.fex
@@ -218,8 +218,6 @@ mode = 0
 [gpio_para]
 gpio_used = 1
 gpio_num = 30
-; gpio_pin_1 = port:PL10<1><default><default><1>
-; gpio_pin_2 = port:PA15<1><default><default><0>
 gpio_pin_3 = port:PA12<1><default><default><0>
 gpio_pin_4 = port:PA11<1><default><default><0>
 gpio_pin_5 = port:PA06<1><default><default><0>
@@ -249,10 +247,6 @@ gpio_pin_28 = port:PA20<1><default><default><0>
 gpio_pin_29 = port:PG06<1><default><default><0>
 gpio_pin_30 = port:PG07<1><default><default><0>
 
-;[led_assign]
-;normal_led = "gpio_pin_2"
-;standby_led = "gpio_pin_1"
-
 [leds_para]
 leds_used = 1
 green_led = port:PL10<1><default><default><0>
@@ -289,13 +283,11 @@ ths_trip2_count = 1
 ths_trip2_0 = 105
 
 [cooler_table]
-cooler_count = 6
-cooler0 = "1296000 4 4294967295 0"
-cooler1 = "1200000 4 4294967295 0"
-cooler2 = "1008000 4 4294967295 0"
-cooler3 =  "816000 4 4294967295 0"
-cooler4 =  "648000 4 4294967295 0"
-cooler5 =  "480000 1 4294967295 0"
+cooler_count = 4
+cooler0 = "1200000 4 4294967295 0"
+cooler1 = "1008000 4 4294967295 0"
+cooler2 = "816000 4 4294967295 0"
+cooler3 = "648000 1 4294967295 0"
 
 [nand0_para]
 nand_support_2ch = 0
@@ -355,7 +347,6 @@ tv_dac_src0 = 0
 [pwm0_para]
 pwm_used = 0
 pwm_positive = port:PA05<3><0><default><default>
-;       If set gamc_phy to use = 2
 
 [gmac0]
 gmac_used = 2
@@ -517,7 +508,7 @@ smc_sda = port:PA08<2><default><default><default>
 [usbc0]
 usb_used = 1
 usb_port_type = 2
-usb_detect_type = 1
+usb_detect_type = 0
 usb_id_gpio = port:PG12<0><1><default><default>
 usb_det_vbus_gpio = port:PG12<0><1><default><default>
 usb_drv_vbus_gpio = port:PL02<1><0><default><0>
@@ -541,7 +532,7 @@ usb_regulator_vol = 0
 usb_not_suspend = 0
 
 [usbc2]
-usb_used = 1
+usb_used = 0
 usb_drv_vbus_gpio =
 usb_restrict_gpio =
 usb_host_init_state = 1
@@ -551,7 +542,7 @@ usb_regulator_vol = 0
 usb_not_suspend = 0
 
 [usbc3]
-usb_used = 1
+usb_used = 0
 usb_drv_vbus_gpio =
 usb_restrict_gpio =
 usb_host_init_state = 1
@@ -676,7 +667,7 @@ spdif_used = 1
 hdmi_used = 1
 
 [s_cir0]
-ir_used = 1
+ir_used = 0
 ir_rx = port:PL11<2><1><default><default>
 ir_power_key_code0 = 87
 ir_addr_code0 = 40704
@@ -709,53 +700,19 @@ ir_addr_code12 = 65344
 ir_used = 1
 ir_tx = port:PH07<2><default><default><default>
 
-;----------------------------------------------------------------------------------
-; dvfs voltage-frequency table configuration
-;
-; pmuic_type:0:none, 1:gpio, 2:i2c
-; pmu_gpio0: gpio config.
-; pmu_levelx: 0~9999: voltage(mV), 10000~90000:gpio0 state. voltage form high to low.
-;
-; extremity_freq(Hz): cpu extremity frequency when run benckmark or demo apk
-;                     1536MHz@1500mV with radiator, 1296MHz@1340mV without radiator
-; max_freq: cpu maximum frequency, based on Hz, can not be more than 1200MHz
-; min_freq: cpu minimum frequency, based on Hz, can not be less than 60MHz
-;
-; LV_count: count of LV_freq/LV_volt, must be < 16
-;
-; LV1: core vdd is 1.50v if cpu frequency is (1296Mhz,  1536Mhz]
-; LV2: core vdd is 1.34v if cpu frequency is (1200Mhz,  1296Mhz]
-; LV3: core vdd is 1.32v if cpu frequency is (1008Mhz,  1200Mhz]
-; LV4: core vdd is 1.20v if cpu frequency is (816Mhz,   1008Mhz]
-; LV5: core vdd is 1.10v if cpu frequency is (648Mhz,    816Mhz]
-; LV6: core vdd is 1.04v if cpu frequency is (0Mhz,      648Mhz]
-; LV7: core vdd is 1.04v if cpu frequency is (0Mhz,      648Mhz]
-; LV8: core vdd is 1.04v if cpu frequency is (0Mhz,      648Mhz]
-;
-;----------------------------------------------------------------------------------
 [dvfs_table]
-pmuic_type = 0
+pmuic_type = 1
 pmu_gpio0 = port:PL06<1><1><2><1>
 pmu_level0 = 11300
 pmu_level1 = 1100
-extremity_freq = 1296000000
+;extremity_freq = 1296000000
 max_freq = 1200000000
-min_freq = 480000000
-LV_count = 7
-LV1_freq = 1296000000
-LV1_volt = 1320
-LV2_freq = 1200000000
-LV2_volt = 1240
-LV3_freq = 1104000000
-LV3_volt = 1180
-LV4_freq = 1008000000
-LV4_volt = 1140
-LV5_freq = 960000000
-LV5_volt = 1080
-LV6_freq = 816000000
-LV6_volt = 1020
-LV7_freq = 480000000
-LV7_volt = 980
+min_freq = 648000000
+LV_count = 2
+LV1_freq = 1200000000
+LV1_volt = 1300
+LV2_freq = 648000000
+LV2_volt = 1100
 
 [gpu_dvfs_table]
 G_LV_count = 3
@@ -833,5 +790,4 @@ key5_vol = 2000
 d7s_used = 0
 din_gpio = port:PD00<1><default><default><1>
 clk_gpio = port:PD01<1><default><default><1>
-stb_gpio = port:PD02<1><default><default><1>
-
+stb_gpio = port:PD02<1><default><default><1>
\ No newline at end of file